i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
We have the following problem when start the watchdog from bootloader: the application is started successfully by the bootloader but when enable the softdevice the application...
Hello, I'm implementing a pair of MCUs where one is operating a ANT+/BLE radio stack using the S332 soft device. Whilst TWIS is disabled, we're getting great performance,...
Hi all , I using module NRF52832 and SDKv14 . I have 2 board central and 2 board peripheral . I want to connect each board central to all board peripheral and connect each...
Hi everyone,
I'm working in an application for a wearable device and I recently have a problem debugging it with Ozone Debugger from SEGGER Microcontroller Systems . I'm...
Hi I am using the mesh sdk 2.0.1 and the nrf52 dk board.
I have made a new model modifying the simple on of client/server example, where the server will send a periodic...
the function nrf_dfu_settings_init in nfu_dfu_setting.c
// Copy the DFU settings out of flash and into a buffer in RAM.
memcpy((void*)&s_dfu_settings, m_dfu_settings_buffer...
Hi,
Our product is based on BLE 4.2 / 5 peripheral devices and PC application (windows 7 & 10 environment) as central device.
we try to use nRF52840 dongle and also other...
On a NRF52DK Board, There is an on-board programmer done with ATSAM3U2C seen as a Segger programmer or a Jlink Progammer.
By mistake, I erased the entire flash of this...
I was trying to update J-link firmware (using link [https://devzone.nordicsemi.com/question/170895/nrf52832-jlink-stop-working-after-entering-bootloader-mode/] ) into interface...
Hi,
The following vulnerability described as Bluetooth implementations may not sufficiently validate elliptic curve parameters during Diffie-Hellman key exchange in the...
I want to use the serial DFU. Do you have any examples? I tried with ble_app_buttonless_dfu, not UART DFU.If you have a detailed reference, please let me know.thank you very...
Hi,
I am using the MCU on a board with sensors that are sampled in a very high rate (~100Hz).
I am having issues when trying to send the data with notification on more...
Hi,
I am using sdk12.2 and customised nrf52 board.
I want to interface ultrasonic sensor with nrf52. In this I am enabling trigger pin as high and after sometime my...
Dear All,
I am working with SDK version 15 and softdevice 132.
I want the device to advertise for 1 minute. Then go to low power mode. Again wake up after 5 minutes...
I have twe NRF24L01 module,one set Tx mode with autoask,and another set Rx mode without autoask,
The channel and address are same.
Can I use this mode to communication...
