Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
nrf52810,sdkV15.0.0
err code:
nrf_gzll_init(NRF_GZLL_MODE_HOST) ; nrf_gzll_enable();
An hardware error occurred when I called the function nrf_gzll_enable()。
but:...
Hi,
I am trying to insert the fatfs code example into my custom project. I already added all the files e dependences and when I call the fatfs_example function from main...
I use SDK15 and ble_app_uart_c example.
static void db_disc_handler(ble_db_discovery_evt_t * p_evt) { ble_nus_c_on_db_disc_evt(&m_ble_nus_c, p_evt); ble_ser_c_on_db_disc_evt...
Hey,
we want to change our product-bluetooth-chip for new products.
In the example the 16 Bit UUID overrides the byte 12 and 13 in the 128 bit ID. Where I could change...
Hello,
I am having interface nRF51 with RF receiver. Output of RF receiver connected with GPIO pin of nRF51.
How can I detect interrupt on gpio pin?
Thanks & Regards...
Hi,
I'm using Secure_Bootloader example of SDK 15.0.0 and I can't get the Logger module to work. I set NRF_LOG_ENABLED to 1, increased memory regions in make file, so the...
Can the esb bugfix timer (currently TIMER_3) be set to another un-used timer without any side effects? I need to implement the async uart from SDK15 and it uses TIMER_3 and...
Is there a simple example which supports LESC Just Works for peripheral mode only? The lesc_multirole example seems a bit too much since that also supports central role. I...
I am sampling 3 sensors using the ADC peripheral, clocking it once every 15us to sample the 3 sensors (3us acquisition time + 2us processing = 5us per channel).
I use the...
hi,
How can i set Destination Address to a particular Mesh Node. so that all message reach that particular Node Only.Since provisioner can set address while provisioning...
how to use app of mesh to send message to node ?
I already got the source code from web: https://github.com/NordicSemiconductor/IOS-nRF-Mesh-Library .
1\ i have add three...
I would like to put a nrf51822 device into system sleep (not off) mode and wake it up (not reset) with a GPIO transition from high to low. I used SDK(nRF5_SDK_12.2.0_f012efa...
Hello everybody, I tried to activate the PHY Coded in the UART Example from the SDK15.1.0 examples.
For this purpose, I have set NRF_BLE_SCAN_SCAN_PHY 4 in the sdk_config...
hello,we are developing NFC on NRF52832 recently,we want to use NFC as a label,T4T,but we have some problems as follows:
1、firstly,we want to develop NFCT by ourselves(not...
hello , i'am working actually on the timer of nRF52840 S140
my timer look like this:
but how to switch from millisecond resolution to microsecond resolution ? ( APP_TIMER_TICKS...
