here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello All
I am planning to install the nRF51822 beacon, wanted to know how to setup so that the beacon broadcasts repeated eddystone based advertisement URL/ packets to...
I am trying to get the nRF24L01+ working with a PSoC 3.
I initialize the nRF like this..
spiWrite1(NRF_CONFIG, 0x0F); // reflect TX_DS, RX_DR and MAX_RT interrupts as...
I have installed this software several times without any result on PC.
How to access an IDE???
I am really very frustrated. Since several weeks I am not able to edit, compile...
When an interrupt with a printf in it triggers while another printf is still occuring the previous message is cutoff to print the next one.
Is there a way I can wait for...
Hi,
I've a custom board which has NRF51822 SOC and STM32 SOC. These two are connected over UART. In past I've successfully performed DFU OTA (BLE) for nrf51822 MCU, and...
I have got a Raytac module MDBT40(nRF51822) and development board nRF52832. Now I want to program the module using the development board. I have followed this video ( Programming...
Hello all,
I am trying to update my firmware using BLE peripheral.
I followed the instructions in this [tutorial] ( devzone.nordicsemi.com/.../)
I downloaded the SoftDevice...
Hello Nordic Forum!
Our product relies heavily in the TWI Bus, we use it to communicate with different sensors periodically. The most "important" one is read once every...
Hi,
We have made a custom board using the NRF52832 chip. The device is in hard fault mode and we believe it may be because of the corruption in internal memory. We wanted...
Hi,
Currently I am trying to test DCDC mode on my custom board nrf52832. After soldering 15nH and 10uH on DCC(pin 47), I issued the following command after softdevice enabled...
@Vidar: I have followed your steps in tutorial for "Development with GCC and Eclipse" and when I try to flash my device I get the below error
Nrfjprog.exe is not being...
Like many others (read a lot of threads here about this and also beneath the tutorial to Eclipse many people write that they suffer for it) i have problems in Eclipse with...
Hi,
I'm using the example dfu/bootloader_secure_ble for NRF52832 (PCA10040 board) in nRF SDK 13.0.0 version and on my mobile the "nRF Connect" application.
If I use...
Hello,
I'm working on a project based on the ble_app_multirole_lesc example, under examples/ble_central_and_peripheral/experimental and I found a bug.
In ble_evt_dispatch...
