Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello all,
I am new to nRF platfrom, I am working on a protect which contains multiple BMD-200 modules with nRF51822 controller. It has to transfer some data via UART,...
Per this blog, I understand that the nRF52's ANT pin must be matched to 50ohm via L1/C3 and that the antenna must be matched to 50ohm. Hence a trace with 50ohm characteristic...
Hello, the title is pretty descriptive.
I've tried to read through previous questions and got a rough idea but decided that it would cost too much time for me to explore...
I am working on a ble application using an nRF51822 that requires low power consumption. I'm curious if on average the observer or the central role will consume less power...
We have our own custom board using nRF52832 (via Laird BL652 module). Until recently, we have been programming our application, bootloader and softdevice using the PCA10040...
SDK12 and SD 132 v3.
I have my code working for HVX from the peripheral. I can HVX send up to 80 bytes on one characteristic in one call (ATT MTU was set to 83 and DLE...
The NRF52 product spec suggests:
"The input buffer of a GPIO pin can be disconnected from the pin to enable power savings"
I've found that gpio.h provides the function...
Here is a snippet of my debug log:
nrf_sdh_freertos: Creating a SoftDevice task.
nrf_sdh_freertos: SoftDevice task not created.
app: ERROR 4 [NRF_ERROR_NO_MEM] at ...
When using radio notifications, there are a few compiler warnings.
Compiling file: ble_radio_notification.c
../../../../nRF5_SDK_14.2.0_17b948a/components/ble/ble_radio_notification...
I've been working with an Adafruit NRF52 Feather board for the last week, and have been struggling to get the board to go into a low power mode. At the moment, I am working...
Are there any publications, from Nordic or academia, that give estimates on what would be the maximum capacity of a BLE mesh network?
I believe there is a hard limit of...
I have created a program on Arduino which does audio/video output and takes input from accelerometer and camera module. I was able to move accelerometer code to NRF52 with...
Hello guys,
My set up is pca10028, s110, sdk 6, tablet with nrf_connect app. I am using modified ble_app_uart example. I was trying to send >20 bytes from nrf_connect app...
hello
Now i am useing the DK of nRF52832 and SDK14.0.0 of ble_app_uart.
I am experimenting to transmit data from external equipment to nRF 52832 and send data to smartphone...
