I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
I am working on the nrf52840 kit with the ble_app_beacon example, compile and download the code successfully. But I don't know how to test whether the kit is advertising,...
I have my own hardware design with the nRF52840 on it. I more or less copied the whole radio/antenna part from the dev kit reference design. The blinky example works fine...
After checking and searching, i found this ble_gatts_conn_cfg_t::hvn_tx_queue_size should be the key to set it. In my custom project (SD132 V5 + SDK14.1) the only setting...
Hi
I'm using IAR Compiler and need to generate some PWM outputs. I tried to use the example code from the pwm_library. But the compiler is generating an Error on the macro...
I am using PCA 10040 development boards with soft device version s132_nrf52_3.0.0 to investigate Central/Peripheral communications.
A PCA 10040 acts as a Central making...
Here is calibration of UART data using ADXL345.
and the data is followed by x, y & z value, for example x = -42, y = 20, z = 268. and then after calibrated 10x which is...
We are upgrading an existing product to use Bluetooth instead of the parallel port.
It must support >20kbit/sec communications between the device and the host PC.
We...
Hey Nordic devzone,
I am tinkering with the following multiprotocol examples:
ble_thread_dyn_mtd_coap_cli (client)
ble_thread_dyn_template (server)
Currently the client...
Hi, I'm using nRF52832 with sdk 13.1.0(softdevice 4.0.2). I had trouble to connect nRF52832 in some android smart device.When I restart Bluetooth,Sometimes there are problems...
Hi, I'm using nRF52832 with sdk 13.1.0(softdevice 4.0.2). I had trouble to scan nRF52832 in android smart device.When i disconnect the device a long time when the status is...
hello,
I use my own code to test IOS message notifications ,
call nrf_ble_ancs_c_request_attrs function， then did not receive the data source,
Triggered the BLE_ANCS_C_EVT_NP_ERROR...
I am following blogs and questions for image transfer with nrf52 and arducam on this site and github . I can see we can use arducam OV2640 module. It has FPGA chip at back...
Hi all , I have a trouble . I am using ble_app_hrs_rscs_relay example . I modify it for NUS service . I have 3 board . peripheral <-> role <-> central via NUS . It work fine...
Im following the example Alert Notification Application and read this instruction:
In nRF Connect, create the Alert Notification Service (ANS) server by performing the...
