Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Apologies for the newbie question. Does this BLE Module need a separate antenna to be purchased? Or are you supposed to design your own with PCB traces? Some BLE modules have...
I want to avoid the soldering of the inside (Becoz of production isse) pins that's why I'm using all the outer pins of the ic. But the problem is RESET pin is inside so can...
Hello,
I am using UART_1 in my program to comminicate with other sensor. So the data is read from UART_1 and print to UART_0. Now I want to communicate with other sensor...
Hi, I am using BMD301 chip on my custom board which schematic i have shown below,I need to enable UART as well as nrf_log in my application. For this I am using SDK 15.3 PCA10040...
I am getting small power spikes but cant seem to pinpoint what is causing them.
The smaller spikes in between the transmissions. (The wave is clipped from the top so the...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
So with the errata in mind the RC oscillator has a accuracy of +/-500 ppm, while the XTAL on the nRF52 DK has a accuracy of +/-20 ppm. During the longest waiting period of...
I have your full eval board as well, I also have multiple NB_IoT sims from Vodafone but have not tried them yet. How do I get your Thingy:91 unit with your sim running please...
Hello,
I want to implement a data logger that will save events in an external flash (even if i think i will start with the FDS). My purpose is to identify some behavior...
Hello,
I am looking to start an independent project this month. One of the tasks will be to use BLE to relay information from a custom PCB board with the nRF52810 chip...
nRF51822
S130
SDK11.0
The power consumption immediately going up high to 1MAH once I enable TWI using this code:
NRF_TWI0->ENABLE = TWI_ENABLE_ENABLE_Enabled << TWI_ENABLE_ENABLE_Pos;...
Hello,
When I added the below lines I get some error:
NRF_BLE_GQ_DEF(m_ble_gatt_queue, /**< BLE GATT Queue instance. */ NRF_SDH_BLE_CENTRAL_LINK_COUNT, NRF_BLE_GQ_QUEUE_SIZE...
Hello,
I have been looking through Nordic's documentation for the nRF9160 and trying to find voltage ranges for several pins but am having no luck. Can someone please answer...
