I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
We are using NRF52840 in our project. Here my doubt is we need to read the voltage from the sensor which will vary from 0 to 5 v .Can you plz tell me which example program...
Hi, I added the SAADC feature to a beacon project so I can measure the battery voltage. Interesting thing is that my readings always show around 100mV less then VDD voltage...
We are developing a small BLE device and want to make sure we follow reasonable security standards. What type of communication security would a typical device like headphones...
Hi,
I want to change the pin configuration for the uart2. I change it in the SES 's Project>Edit Device Tree .
However, if I change the tx pin to 0x0f , it cannot send...
Hello, Is there any NFC sample for Thingy:91 . I need to connect a device to Thingy:91 using NFC for a project. I am using v1.1.0 tag of ncs repo.To understand how NFC libraries...
I need to set REGOUT0 to 3v3 for a custom board. What's the best way to do this using the armgcc toolchain? Right now, I'm setting the value first thing in my main:
Is...
Hi,
I try to write some data into the flash memory, but I always get a hardfault when I try to use the write function provided from the examples:
No I think this...
Hi everyone,
I am trying to start a data length update procedure from a central that I am developing with python using the library pc-ble-driver-py.
However, I keep having...
Hi,
I try to store some variables into the flash memory using the fstorage library provided by nordic. From the example I got the following implementations for testing:...
As I mentioned in my other question , I've been playing around with the bearer layer of the Mesh-Stack, to get a better understanding of how to get a robust basis for a multiprotocol...
Good day! Tell me how you can configure access to UART with DMA in the example freertos_coap_server for receiving and transmitting arbitrary messages. Also, please clarify...
I am using this sample https://github.com/NordicSemiconductor/Android-nRF-Blinky . I noticed that when device rotation is changed the device stills connected.
I changed...
Good day. I can't find the schematic of the EVAL NRF52-DK version 2.0.0. The previous version I used was 1.2.4 where I cut the following welding points for testing.
SB22...
I am able to log information to the flashlog backend. When I use the cli interface "flashlog read" I see my information stored (e.g. "operation took %s seconds to complete...
I am trying to download the NRF UART and Nrf Toolbox service the same ones used in the playstore are different than the one on github. The NRF UART v2.0 is different and doesn...
