I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi everyone,
I'm working with the nRF9160 and trying to configure P0.19 as the UART TX pin using Zephyr. Here's the configuration I used in the device tree:
uart1_default...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
Hello,
I am using nRF Connect SDK v3.0.1, together with the Find My add-on. Test case TCG013 of the Find My Network Self-Certification Test Cases R1.7 is failing on the...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
HI: D:\ncs\v3.0.0\nrf\samples\bluetooth\peripheral_uart Using the nrf54l15DK board can run peripheral_uart examples,connection is disconnected. However, when I use the nrf54l05...
Hi,
I'm working on software for a design incorporating an Ezurio module that uses an NRF54L15 chip.
I'm currently using the peripheral_uart example as a base for early...
Hello!
We are planning to implement OTA update of an application and a second stage bootloader in our product. As a bootloader chain, we will use NSIB + MCUboot as the nRF...
Hi Team,
I am currently working on a project involving the Nordic nRF DK IDE and the Matter protocol. As part of my learning process, I watched your YouTube video and followed...
I'm an engineer to develope smart ring, it's a very small devie and need to use very small IC.
I'm looking for nRF5340 + nPM1300 reference schematic for this development...
Hello,
I'm currently working with a custom board using the nRF5340 SoC, and I'm running into unexpected current consumption behavior.
When the device is in advertising...
Hi,
I was at the webinar today where they talked about SDK 3.0.0. They mentioned that the QSPI examples were "JESD216 flash" and "JEDEC SPI-NOR flash". I don't see either...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
I am trying to implement LittleFS on 1Gb QSPI NOR flash (W25Q01JV) on the nRF5340.
I am running nRF Connect SDK version 2.4.2 and am using a slightly modified version of...
Hello. I am using nrf52832 for Ble-based positioning. currently i am tackling with establishment of an anchor measuring rssi values and sending them to a central center (a...
Hi,
I am trying to run the nRF91x1: DECT NR+ Shell example on my nRF9161 SDK board.
I get this crash when the code runs
Can you point me to the explanation of what...
We're building a prototype board which uses the nRF52833 and want to tune the RF components. The radio_test sample in SDK 3.0.0 doesn't seem to support the nRF52833 SoC. Is...
Hello,
I've an issue that I can't find clear instructions for the nRF5340 serial recovery for the network core.
Being able to update both cores from the bootloader level...
It seems the "reset" button on my nrf52840dk doesn't do anything anymore. I believe this started happening after I enabled mcuboot in sysbuild. Is this expected?
I am using nRF54L15 with Zephyr to measure voltage with ADC. In the struct adc_sequence there is a calibrate bool, but I am not sure what it does. What is the reference that...
Hi,
Does Central or Peripheral UART enable ACK/NACK in the code for BLE communication? How does Peripheral recognize if Central has received all the data ? Is there any...