Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello,
I would like to use nRF52810 chip.
And I want to implement PCB trace antenna and PCB chip antenna on same PCB(for provision)
Either PCB trace antenna or PCB chip...
I am using the SPI peripheral for communicating with a network through long wires. Is it any information about the impedance of the driver outputs from the nRF52832?
I will...
nRF52840 OPS v0.5.1 section 16.16.2 states “A pin reset is generated when the physical reset pin on the device is asserted”. This seems to contradict the descriptive name...
Dear Nordic
All our last SDKs in "example/dfu" have same error.
Code is not corect:
nrf_clock_lf_cfg_t clock_lf_cfg =
NRF_CLOCK_LFCLKSRC;
Impossible properly...
Hi Nordic Support,
According to the answer in question:
devzone.nordicsemi.com/.../
it is not possible to update the bootloader (which is the case with "bootloader_secure_ble...
I am trying to set up RTC2 by following an example
github.com/.../saadc_low_power
I ported it to my project which is running a softdevice on nRF52. It works perfectly...
Hi Alls,
I'm trying to compile and test the example project from SKD_12.3.0 and receiving the following error:
#error app_timer for freeRTOS requires configUSE_TIMERS...
Hi everyone
I'm doing some basic test to verify the correct platform for a future project, we need ble long range, therefor we are testing the NRF52840-PDK
I have loaded...
hello,we use nRF24l01+ for the communication of IoT.There are a lot of terminals work at a same channel,when the controllers send CMD,we have found:the length of reading from...
Hello,
I am having a weird reset behaviour with my nrf52832pca10040, SDK12.2 with softdevice v3.
I have connected an acc into the SPI interface through these pins
...
Dear friends,
I want to measure the current of RF of BLE using PPK. However, i do not care the current of other peripheral devices, such as timers, pwm. How can i make it...
Hi,
We have nRF51822 acting as a central and another nRF51822 acting as peripheral. The peripheral advertises at 1 second advertisement interval. The peripheral and central...
Hello,
There is a characteristic with properties:
memset(&char_md, 0, sizeof(char_md));
...
attr_md.vloc = BLE_GATTS_VLOC_USER;
...
char_md.char_props.write = 0;...
Hello everyone~
BLE 4.2 secure connection is very useful for smart automobile. It's fit for many lock/unlock and rent/sharing scenes. Is there a plan for automotive grade...
