I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
I want to write data longer than 20 bytes on Android MCP.
But if I use "write command", only 20 bytes data can by successfully written. The rest data is lost.
If I use ...
The last time, i could wireless communication by pressing a botton.
The next time, i wanna send the data to phone if the communication is established.
i modified the source...
There are already a few threads about this problem but none of them helped.
I want to use GPIO9 + 10 as .. well .. GPIO.
Here's what I did:
added CFLAGS += -DCONFIG_NFCT_PINS_AS_GPIOS...
hi,everyone,i use the nrf52832,sdk11.Every now and then my hardware has reset,and l use the "NRF_POWER->RESETREAS" to read the reset cause, and the NRF_POWER->RESETREAS value...
I have gone through the SDK and from what i basically understand is that gazell and BLE Multilink look very similar from the application point of view(1 Host connecting to...
In the nRF5 SKD alpha, gatts_cache_manager.c:123 looks like this:
gscm_evt.params.sc_state_stored.state = &peer_data.p_service_changed_pending;
Is this supposed to...
Hi all,
Refer as the antenna whitepaper, The Zs = 50 Ohm pi network need to match. I saw a matched pass filter optimized for nrf52832 from Johanson (Part Number:2450FM07A0029...
i have app_ble_uart and i wan get temperatura with my phone main.c terminal there is my code but i dont had any msg from my BLE controller.But if i changed call of function...
Hi, iOS caches services and characteristics when bonded with device, so we need to inform him to invalidate this information via Service Changed characteristic, but how it...
So I switched from Bluemod+S (nRF51822) to Bluemod+S42 (nRF52832) on my custom board and am trying to adapt my existing code to work on the newer model. Apart from various...
Hello,
can anybody tell me the exact differences between a Link Layer Acknowledgement and the Acknowledgement used by a write Request?
Does anybody have some statistics...
I am trying to implement the Current Time Service in my project and had a few questions:
-The example requires that security be established before services can be discovered...
hai
i am using mbed to program my nrf51822. in my application i need to read two analog sensor values.
i am using p5 and p6 pin for that.
AnalogIn analog_pin_1(p5);...
Can somebody explain what 0xA1 means in this raw L2CAP layer:
0a, 00, 4d, 00, A1, 01, 00, 00, 08, 00, 00, 00, 00, 00
I know 0a, total bytes, and 4d is channel ID, I...
