Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
Just want to confirm I can be i2c master with zephyr rtos for nrf52 pca10040.
In link ( devzone.nordicsemi.com/.../) titled "nRF5x support within the Zephyr Project RTOS...
Hello everybody!
I have one nrf52840 DK and nrf528323 DK. I was flashed and test throughput example. I reach 450kbps. ( transfer 1Mbyte in 18s). Can I enhance this speed...
Hi,
We are interested in nRF52840 and we know that nRF52840 supports both on IEEE 802.15.4(Thread, ZigBee) and IEEE 802.15.1(BLE).
However, does nRF52840 can run BLE...
HI
I'm studying how to control mouse and keyboard via HID with nRF24LU1+ module referring to firmware of nAN-22.
Even though I set Descriptor as appropriate for mouse...
I'm using FDS and define record_chunk.length_words 173.
system waits for fds operation is finished and in the meanwhile, system sleeps using sd_app_wait().
Then, sd_app_evt_wait...
Hello
i am using BLE Relay example with softdevices 132 and sdk version 13.
i make this example simple, no more connection.
just adverting and scanning continuously. here...
Hi all,
I'm using nRF52840 and S140 based on the ble_app_uart example. I get a error code 4 when use sd_ble_gatts_characteristic_add to add a characteristic for another...
Hello,
Help me, please.
I am testing ble_app_uart. Softdevice is S130 and SDK is nRF5_SDK_12.2.0_f012efa.
My development board is Waveshare's NRF51822 Eval Kit.
...
Hello,
I'm writing an application that uses the SAADC and would like to set up a high limit to trigger on.
If I use the following code, I'm able to trigger 1 ADC sample...
Hi,
I plan to design a system of 51822 that includes 1 center and 2 devices. And 8K Bytes data should be transmited from each device to the center per second simultaneously...
Hi, I am using a two nRF24L0+'s.
One for TX and one for RX. Transmitting in one direction only. There is sometimes a packet arriving out of order. Every minute or two....
I use ESB sample code ,change to do 8k sample rate ADC(10bit) and transport by ESB ,but overflow when output receive data to PC use uart at UARTE_BAUDRATE_BAUDRATE_Baud1M...
