I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi, I have an Adafruit Feather52 board which is preloaded with a serial DFU bootloader and the S132 Softdevice, of which I also have the merged Hex file. I would just like...
Hi,
I am designing a custom PCB using the nRF51422 chip. I have a program that I developed on the nRF51-DK. The program reads the capacitance value of a proximity sensor...
Hi All,
i need some helps. I need a device that can connect with one phone only, so i have created a whitelist wih size of 1.
During the life of device the device can...
Hello, I'm pretty sure the new BLE 5 will come out soon and it will integrate the mesh. And if mesh needs to be done at a protocol level, it must be the softdevice.
So...
Hello iam using softdevice 110 and SDK 10.0.0, i have implimented dfu in my project, i want to update a region in EEPROM by calling pstorage_update() function before calling...
A while ago I asked this question devzone.nordicsemi.com/.../.
Yesterday I re-installed MDK 8.11 after a computer crash and I had IAR version 7.60.1 and version 8.11.2...
Hi,
I need to design a small nRF52 board On 24mm Dia 2-layer PCB, same like nRF51822 Bluetooth Smart Beacon Kit (nRF51822 Coin-Cell design). Please find the attached Schematics...
Hi everybody.
I encountered issues with the formentioned setup. In my project I'm using latest SDK 13.1, softdevice S132 v.4.0.2. I'm compiling the project with latest...
Hi to everybody,
I am working with a custom board based on the nrf52832, while trying to integrate to my existing application the DFU functionality I am having problems...
I am trying to measure the ADC on all 8 ADC pins of the nRF52 on the PCA10040. I'm noticing quite large amount on noise on floating lines (up to 0.6V). However my biggest...
We have a device with a main MCU connected to a NRF52832 for BLE communication. Our device have Battery, Heartrate and a custom service. The first implementation used a Sparkfun...
I am trying to decide what Nordic solutions would best support the application throughput requirements seen below. Distance requirements are low (1 meter each link).
...
Hi there,
I have nRF52840-Preview-DK eval board. I have downloaded the “SDK 13.1.0”. I was trying out the power management example under the folder “..\nRF5-SDK_copy\nRF5...
