Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I'm calling sd_ble_uuid_decode with the following parameters on a PCA10040 board:
sd_ble_uuid_decode(16, 0x2000F7CC, 0x2000F7DC)
ram base = 0x20003150
vs_uuid_count...
I want to use in my project tft 1.8 display with st7735 controller. I used the standard GFX example from SDK 14.1 and everything is working fine, but the picture is incorrectly...
I have a QFN48 nRF52832, and it's getting hot. I'm looking at it with a thermal camera and there's a hot spot directly under the "N" of the "N52832" that's on the package...
The BLE_NUS_C_EVT_DISCONNECTED of the ble_nus_c_evt_handler() give a conn_handle = BLE_CONN_HANDLE_INVALID . So it's not possible to know which peripheral got disconnected...
Hi everyone !!
I'm a beginner in ble mesh. I'm working with nRF 52840. I'm not being able to figure out how to see log messages. I want to know where will following line...
Is there anywhere I can find some high level documentation on the FDS module? I'm going thru the API documentation but it provides very little insight into how to best setup...
Hi Nordic Devzone,
First i want to make sure that if the clock being used by softdevice is the LFCLK (32kHz) and its counter register is 24bits ? and which prescaler is...
Hi Guys!
I am a newbee to develop a BLE IoT, and I am really trapped:
first of all: I am using the UART example from the SDK (12.2)
I'd like to send a float array with...
Has anyone been able to successfully connect a BLE device to nRF Cloud using an Android device as a gateway?
I don't see many posts or discussions around this topic. After...
Hi,
I am developing an application, in which I need to store the data collected from various sensors in external flash, in a particular format (Dataset no. - Sensor1 data...
When I use sniffers and wireshark for debugging (ble_app_uart), I found a strange place.
The following are the empty data PDUs seen from wireshark:
50ms:
Master-...
Hi,
I want to use battery service in my beacon for that i have tried two examples of sdk14 on nrf52 dk
1)ble_app_hrs
2)ble_app_proximity
in first example ble_app_hrs...
Hi,
I am nrf52832 SDK14 .
Can you provide a simple example of IRK implementation to resolve the peripheral address in SDK 14.It will be helpful to get insight of it. ...
Hi,
Do you know why I get a warning : Unable to allocate memory for relay packet. ?
I am trying to mesh 2 servers and 4 clients. with client capacity 3 for each server...
Hi,
I'm trying to run the gdb on the nRF52 with softdevice s132 and in the begining it runs ok but after some time when I run (gdb) list I get: "Line number 435 out of...
