Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
When I test the timer example with nrf52832 DK, it so nice to 4 minutes.
uint32_t time_ms = 240000;
But when I set the time interval over 5 minutes, then the event...
What is the maximum number of bond table entries a device can have?
If a device allows only one connection to be established at once (not more than one simultaneously)...
Hi,
I want to store the CRC of the current firmware in the flash, for DFU purposes. Almost all of the threads I've seen so far reference the pstorage API but it's no longer...
I am searching for a basic example to understand the build system.
How do I load the soft device properly?
How do I set things up to run SEGGER_RTT_WriteString?
I...
I am using Nrf52832 sdk 11.I want to update the value of characteristic on every read operation from my andriod phone. I want that on every ble_gatts_evt_read: should give...
Hi! Im trying to figure out the power consumption of two types of beacons that uses nRF51 and nRF52. I have connected a small resistor in between the supply and measuring...
Preferrably under linux using gcc and the command prompt.
I am most interested in project setup, loading the soft device, and making sure all the core systems are working...
I am running the ble_app_uart example in SDK 13.0 with nRF52382.
First issue
The app can receive data via UART only when I use "Termite" as a terminal emulator...
Hi, trying to implement timeslot api and stuck with TIMER0.
I saw similar questions but answers is still unclear.
My timer init code:
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;...
Hi
I am using nrf52832 with softdevice s132_nrf52_3.0.0.
In my appliocation I need to do periodic measuremets, and it is critical that softdevice doesn't interrupt during...
Hi,
I have to make a interrupt each 100us. This interrupt should be priority on the BLE. In my interrupt I have only one condition (if/else) and I have to change PWM value...
Hello,
I'm looking to implement the OTA on my nRF52, but I couldn't find any help online.
I would like to do it with my iOS and my Android app.
Does anyone have a tutorial...
Soon we will start production and this is my first time using a Nordic chip. During production I want to test for output power en center frequency with a development kit as...
I'm trying to create a connection between Android 6.0 and nRF52832. I created a service, like in tutorial, added it's uuid to adv packet (I seeit in nRF Connection). I can...
