I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hi there,
I'm using ASUS RT-AC1900P router with IPv6 DHCPv6 on. RPi gest its own IP with prefix specified in router but interface wpan0 (wpantund) not. I have configured...
just like the title.
I'm using sd_radio_session_open APIs very similar with
https://github.com/nordic-auko/nRF5-ble-timesync-demo
and add data uploading by gatt.
using...
Hi, all!
Sorry, I'm not good at English myself.
My device is nrf52832. Base code is ble_app_uart (sdk 12.0.0, pca10040, s132).
ADD. fs_sys_event_handler
ADD...
My develop board is nrf51822 and the SDK version is 9.0 softdevice s130. Because the NRF51 board is build by the customer. So the UART connect pin is changed from {13,14,12...
Hi, I am in the schematics phase of a new device which may talk via BT to lets say a mobile phone. The communication between the new devices CPU and the nRF52810 shall be...
I'm trying to connect my nRF51 dongle to the DK using the Master Control Panel3.10.0, but I keep getting "no response from master emulator" and failed discovery. I read the...
How do we go about adding servers to the light control example i.e. I would like to control 50 servers via one client. What needs to change in the code besides SERVER_COUNT...
I am modifying the BLE UART example, client and server, in order to have a higher throughput. I have selected that the connection interval is 7.5ms with a total number of...
Now I'm done from send data to the light_client light_service, but I don't know how to send data to another light_server let light_server, I look at the related documents...
I am having issues with the pin_change_int example. I have not changed anything to the code, but it will not load onto my board. In fact, pressing load in this project doesn...
I am trying to implementing eddystone for my nRF52832 and I found two library.
One is with the " /examples/ble_peripheral/experimental_ble_app_eddystone " inside nRF5-sdk...
Hi, I want to NFC connection. so I'm trying to NFC examples.
But, while i was testing NFC_writable_ndef_msg example I have some trouble.
Following the example, I succeeded...
Hello everyone I have a problem where I want to know when a node (server) connects to the gateway (client), how can you control which node, for example, turns light on and...
Hello, I am trying to run the SAADC example code alongside the ble app hrs example. I am able to run both examples individually just fine but when I copy them over to one...
Hello,
I need to implement a simple and minimal serial cable replacement using BLE SoC and external MCU host interfaced by 2-wire UART (without flow control). Is it feasible...
