Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hello everyone,
I'm trying to implement the bootloader from SDK v14.2 on the nRF52840, SD v5.0.0 s132 (using our board and app).
For my testing, I erase the whole flash...
Hi Forum,
i've started the development of an custom service on a nrf51822 with s110.
The Service contains 4 Characteristics where notifications are enabled.
At the...
I have a custom dongle that connects to the PC through a USB-UART chip. It is based on the nRF51822. I have another board based on the nRF52832. This board needs to be able...
Hi,
I am building a device to act as an iBeacon, with other services layered on top. This is based on a Raspberry Pi with a Class 1 USB Bluetooth dongle.
I need to be...
Hi everyone, I'm working on the nrf51822 QFAAH I tried to flash the ble_app_uart example and it didn't work. So I debug it and it stops here
As you can see in the picture...
I am working on app_uart and buttonless_dfu. Although i am getting certain errors which i am unable to counter.
.\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined symbol...
I have 32x64 RGB LED Matrix, and I want to use nrf52 to control it. I got the driver working and I can display everything. It is a time interrupt driven driver, just redraws...
So I just got my nRF52_DK, got everything installed and compiled an uploaded the blinky example. Fine. I had my custom PCB ready, and got the 52832 soldered in straight away...
Hi, I am a newbie to embedded development. I am well versed with java script. I am under the impression nordic allows you to communicate with java script to the development...
Hi, we're using \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hids_keyboard to test Pairing/Bonding/whitelist.
After connection, when the central try to read...
Hello,
We have constructed a custom board of nRF52832 via I2C communication with sensor and INT based wake up. Following configuration enable
DCDC Power Enable
Disconnected...
When I was using a master slave integrated host, when I quickly disconnected the connection and then set up the connection immediately, it was found that the original disconnected...
Hello,
is there a simple example for reading out a value? The nRF5 is in this case a BLE peripheral server. The central device should only read one value at a certain time...
Hi:
I output a PWM channel in 16kHZ,i found that when i set the duty cycles 50%,my tft screen(i2c) display at a very slow speed,and it will be OK when i set duty cycles...
Hi,
I am trying to add a notification charactersitics on client, I am able to add one of them, but when i try to add another one sd_ble_gattc_write(), result is always NRF_ERROR_BUSY...
