Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I am using nRF51822 BLE nano with mbed IDE. I tried to set channel so that i can achieve the desired frequency for FCC testing i.e. 2402MHz,2441MHz and 2480MHz .I am...
I am looking at the ble_app_hrs_c example (with the s130 soft device on pca10028 dev board). I have set the m_scan_mode to BLE_WHITELIST_SCAN to enable whitelisting. In the...
I have implement the systick with the idea to use it for delay functions.
The systick is running normal if no BLE Events occur, but during a BLE event it seems to be stopped...
Do conditional breakpoints work in Keil uVision5? I open the Breakpoints window and see:
If I set count to any value, I application still breaks on the first pass. When...
Hi
I have problem make the examples in the SDK 11. I get at "No rule to make target"
C:\konskimo\NYII\Spec\nRF52832\nRF5_SDK_11.0.0_89a8197\examples\peripheral\blink...
Hi,
when using timeslots I cannot turn off the external crystal that causes an higher consumption.
I already read this post and tried to turn off the timer0 (using STOP...
Dear Sir,
I merget (Software Device) + (DFU bootloader) + (Application firmware) into PE280_WS.hex
And use the script <<nrfjprog.exe --program PE280_WS.hex>>
it reported...
I'm having trouble building the ble_app_uart example in: SDK11/examples/ble_peripheral
My build environment is:
Ubuntu 15.04
SDK 11.0
GCC
S130
PCA10000
nRF51822_xxaa...
Hi,
I have a pretty hard time to get I2C/TWI running on my 52832 Dev-board (pca 10036).
My problem is, that i do not get any physical I2C signal out of the board's pins...
Hello, this might be a silly question, but i've seen various Nordic examples and i don't know whats the difference?
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(500, UNIT_1_25_MS...
nRF52 series compatibility matrix says that you can get the IC revision using nrf_ic_info_get but it is only implemented for nRF51. Does the following patch add support? ...
I am attempting to follow the BLE UART tutorial and everything seems to be going well until I fire up termite and try it out. My phone successfully recognized and connected...
hello,
Every example of nordic is done with only one main.c file , i want to have a
separtate new.c and new.h file and take all the code from main.c and put it to
the...
Hello,
I am using SDK version 9 with softdevice s130 operating as both a central and peripheral. I provide a custom peripheral BLE service, and when it receives some information...
Hello,
I tried to use the example of SPI slave with the sdk 10.0. But I have an issue: the character "Ignored Transaction" is send on MISO pin.
I would like to now why...
