I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi Team,
We recently received our custom PCBs and are currently trying to configure pins P1.00 and P1.01 as UART0 RX and TX respectively. However, the UART communication...
Hi ,
1.In the example: In nRF5_SDK_17.1.0_ddde560_usbd_msc_1\components\libraries\block_dev\qspi\nrf_block_dev_qspi.c, I need to set the following 0xB7 bytes. How should...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm following these instructions. And downloading a project from this github repository.
The downloaded github zip file contains the following folder "ble_app_uart_c_S120...
Hello,
I use this program.I take values.Android Application want to show the values.
Program:
#include "ADXL345.h"
ADXL345 accelerometer(p5, p6, p7, p8);
Serial pc...
Hi all,
I would like to use the Arduino programming environment on my nRF51422 prototype. I have seen that RedBearLab has done the migration for the nRF51822 which quite...
Is the nrf52832 developer kit compatible with Arduino Leonardo? I know that most Arduino shields work well with Leonardo, but a few have troubles.
Thanks
Hi,
I would like to have a recommended supplier for the 32MHz crystal. I have seen the specification for the crystal. But from my experience it is a bit more complex than...
I followed the guide of this and when I opened the project " BLE_Gateway" ,it showed that the "spi_slave.c","softdevice_handle.c"and "ble_advdata.c" file couldn't be found...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
I have a fully working project that uses the HomeKit SDK 1.0.0 from Nordic Semiconductor.
In order to be compliant with Apple specs I am trying to upgrade to version 2.0...
Hello,
I enabled debugging in keil v5 for the nrf 52 and I am debugging through UART for the ble_app_proximity and viewing the messages in putty. The messages i received...
hello everyone,
I was trying to turn off nrf51822 on some condition. So i thought i will use systemoff mode register to do that.i am attaching code snippet of what i am doing...
I am trying to build the ble_app_hrs using gcc. It seems to build okay. I can program it to the device. When I press button 0 or any of the buttons the leds does nt light...
Hey All,
Just trying to get some advice/examples on how to incorporate notifications into a Custom Service on a nrf51 Dk board using gatts. I have found a couple of examples...
Hallo everyone. I'm working with the processor nRF51422 with S210 softdevice and I would like to ask you if it's possible to drive results of LPCOMP to a General-purpose I...
