Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I noticed the following compile time issue in the SDK - both 10 and 11:
The file ./examples/ble_central/ble_app_hrs_c/main.c
needs:
#include "app_uart.h"
For...
Hi,
Could anyone give some advice how can I let 51822 works in RFID mode.
Can RFID work together with BLE? Or is there anoter HAL support like Softdevice? Where can...
Interrupt_Sleep.txt
Currently, I'm trying to use external interrupt that generated by ADXL345 to wake up the nrf51822 after sleep but not working as i want. Kindly check...
I'm had develloped some software and tested it on the nRF51-DK.
After that I made my own PCB design where only the nRF51422 is replaced by a nRF51822.
When I flash both...
I have a legacy RN42 BT2.1+EDR running in a system as the network master that I need to connect/pair with a nRF51422 BLE dev kit, and am having problems.
The BLE just doesn...
HI All,
I tried to migrate from nRF51_SDK_10.0.0_dc26b5e to nRF5_SDK_11.0.0-2.alpha_bc3f6a0
my migrated ble_stack_init:
static void ble_stack_init(void)
{
uint32_t...
I will try to use the s110 8.0.0
But I can not find the sdk installer from the website.
Three months ago, when I visited the website, there is a SDK 6.xx.xx Installer...
Hi.
I'm currently receiving advertisement packet from beacon scanner app. (nrf51822)
(ble_peripheral/experimental_ble_app_multiactivity_beacon/hrs_scanner)
I tried...
Hi, I am here in the use of Flash memory data when there is a strange question to consult.
Due to my side of the application, you need to enter each case sd_power_system_off...
Using nRF51 SDK 10.0, it seems like many debug prints are incorrect, triggering a GCC format warning resulting in a compilation error with -Wall turned on.
A workaround is...
I'm using a custom designed PCB around the NRF51822 that broadcasts accelerometer readouts on a characteristic.
The application is based on s110 uart example and has been...
i wantto compile ''ble_app_hrs_c'' from sdk
but it always show up likes
" C:\Program Files\CodeBlocks\MinGW\include\SDK 7.2\examples\ble_central\ble_app_hrs_c\main.c|19...
keil use pclint, it will give lots of info message or warning message.what 's the best configuration to filter these info message ?? just display the error or warning message...
Hi
I'm trying to test UART over BLE using A custom board with a nRF51822,S110_NRF51822_7.1.0
SDK 6_1_1, Code is Github "NordicSemiconductor/nRF51-ble-app-uart-static-passkey...
