Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
It's the first time i'm using the spi to connect various slaves, so is there any example how to communicate a raspberry with 2 or more nRF24L01 on the same bus?
Thanks in...
Today I have recieved the new nRF52 Development kit PCA10040. I did a update for the nRFgo Studio to version 1.21.2.3.
The softdevice s132_nrf52_2.0.0 will be flashed without...
OS: Windows 10
Target: nRF51-DK
Tried to connect with nrf51-dk with Keil MDK-Lite v5.18a.
The default Jlink version used along with this IDE was v4.98e
the 'download...
Hello all,
I'm looking at the example projects and ble_app_template in particular, and have noticed something that doesn't seem to make sense...
In main(), this project...
Hi, I am looking for a Bluetooth Low Energy Soc based solution like nRF51822, but I'd like to have an open source firmware solution...
Do you have that kind of solution...
Hi
I want to execute my app from the RAM to test if i'll get a considerable decrease in the current consumption.
I'm using : "s130_nrf51822_0.9.0-1.alpha" &"nrf51822QFAC...
Hi
I'm trying to change TX power and measure the current consumption while advertising, (DC/DC disabled) and i get an increase of 3.44mA from 0dbm to 4 dbm. Ok That's logic...
I follow the instruction and I am able to connect to Xively MQTT service. But I am confusing how to connect to AWS IoT MQTT.
AWS claim it support IPV6 as well.
Is there...
Hi all:
Here is my develop environment and it always show the message "one or more breakpoints could not be set and have been disabled".
Is any item I missed.
OS:Ｗｉｎ１０...
The ble_app_gls example does not provide any handling code for BLE_GAP_EVT_TIMEOUT, BLE_GATTS_EVT_WRITE, nor BLE_GATTS_EVT_HVC. I'm trying to understand whether the lack of...
I just ran a few experiments on calling sd_ble_gatts_hvx() multiple times based on SDK v10's ble_app_uart example. I have configure the app so that it for each external event...
Hi, I am using NRF51 Dongle to receive transmitted data from the NRF52 DK. currently , I want to send multi packets per connection interval. my question is that does the dongle...
