I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I want to make The Thingy91 a bluetooth peripheral device . I want it to send the generated temperature data to cloud or another device. How do I do this? I had problems with...
Hi Nordic Team,
Please share logic to scan specific peripheral devices which are advertising with a filter other than filter for device name, uuid, short name and MAC address...
Hi,
I am using nRF52832 with SDK v16 with s112 BLE stack.
I am trying to enable the DIS service like below:
The device can boot successfully but when I checked the...
Hello,
I want the scanner to receive both AUX_ADV_IND PDU event and AUX_SCAN_RSP PDU event for the case when AUX_SCAN_RSP PDU will be lost I still want to have AUX_ADV_IND...
Hi,
I am using RTT log with nRF52832, my question is when debug port is disconnected, what will happen to RTT logger?
Will they be simply ignored? or will the debug pins...
Hi.
I want to measure the current on the nrf 52840. I have downloaded the beacon example on the board and I want to measure current when the beacon is transmitting(LED 1...
Hi,
I am developing an application using BMaD 300 Eval board nrf52. As a first I want to display device information along with MAC address of BMD 300 I have, in advertising...
Hi,
I loaded bootloader, SoftDevice, and Application using nRFConnect - Programmer. But it doesn't launch the application. It fails at
nrf_bootloader_fw_activate() with...
Hello,
I want to read the values from MPU9250 magnetometer i.e. from AK8963 I wrote a function just like accelerometer and gyroscope shown below:
uint32_t mpu_read_mag...
Hi!
I'm looking for a new Bluetooth module for a controller, and I run across the nRF51. I used to have a module that I controlled from the MCU, but this SoC looks like...
I am trying to use the NRF_LOG system with FreeRTOS. In the case of an ASSERT, I want to be able to:
1) log the location of the assertion
2) flush the logs over RTT
...
I’m using the library pc_ble_driver_py last release 0.14.1, and Nordic DevKit PCA10040. My goal is to set the central IRK value and generate a private resolvable address....
Hi, i am trying to build a ble beacon for personal asset tracking. The one that is like Tile or Trackr. What kind of chipset and program that i should use.
Hello
P airing: Just Works with Bonding: Passkey Entry, Peripheral Displays works for bonding.
I want to make LESC Pairing: Just Works with Bonding. Is it possible? According...
I got a vague "cmake did not complete" error from studio when the sdk was installed at a hgfs mounted disk. It worked ok when the sdl was installed at non-mounted directory...
