Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I have a question regarding the nrf52 UARTE driver. I have the basics setup and working, I can send and receive data using the UARTE.
What I need to do now, is find...
Hi all,
Someone, please, can give me an information about programming a board nrf52832 using the pin SWDIO/SWCLK.
There is an application note that explain this topic...
I don't know where to submit these things.
I don't fully have my DFU working yet, but clearly I have a badly formatted init packet. However, the resulting behavior was...
If an app is advertising on all channels, and receives a SCAN_REQ on 37, will it transmit the ADV_IND (and potentially SCAN_RSP) on 38 and 39, or is advertising interrupted...
I am attempting to use sscanf() on nRF51822. However the chip simply freezes when reaching that part of the code. Do I need to add anything in the toolchain to make it work...
I'm using nrf51, I noticed that when I disable some functions calling (in the file flash_memory_management.c ), the behavior or the function in the file ( fatigue.c ) is correct...
Hello ,
Easy question, I am using the nRF52832 and am trying to find out if all gpio pins have gpiote functionality? And if so can all gpios be configured as an external...
hi
this is my timers_init(); func
static void timers_init(void)
{
uint32_t err_code;
// Initialize timer module.
APP_TIMER_INIT(APP_TIMER_PRESCALER, APP_TIMER_MAX_TIMERS...
I am writing an App for the Central/Master side using the s130 v1.0.0 SD. I am connecting to the soft device using the python wrappers for the nRF51-BLE-Driver-Win 0.5.0....
I want to write a program in Keil by SPP for communicating with a thermal printer that uses SPP
but I can't find source code about that.
Is this possible to do this with...
Hello
i have nrf52 PAC10036 dev Board.
i am using the visualgdb.
when i try to create the instance of the TWI.
i got the error
please check image for detail.
How i can...
I want to turn off BLE-peripheral Advertising for 8 hours but I want to use another timer with period of 50ms to scan GPIO ,
when I change prescale of
APP_TIMER_INIT(APP_TIMER_PRESCALER...
Hello,
is there a good documenation or introduction about the Programmable Peripheral Interconnect Feature? I read the short part in the Objective Product Specification...
Hi everyone,
I need to use an nRF51822 (MBH7BLZ07-109033) mounted on a custom board.
I want to develop my firmware application on the custom board in such a way I can...
