Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Hi,
I want to check if the FW is properly loaded into the chip and the chip is locked. Reading APPROTECT hangs the chip even if SD is not enabled. I assume APPROTECT is...
Hello,
I work on application (written in C, compiled with GCC) which use pc-ble-driver 1.0 and nRF51822QFAC with the ble_connectivity (S130 v2.0.0) as BLE Gateway. I need...
Hi,
Anyone around that has good experience designing nfc antennas?
I'm in need of a pattern that is about 50% the size of the flex that comes with the nrf52 kit.
Doable...
Hi @ all.
I have a strange behaviour that I can't get rid of. But first some specs:
SD130 (2.0.0)
nrf51822
SDK 11
custom board
I have an application...
Hello, I'm south korea student in dongguk univ.
I use keil uvision4, nrf51822, s110 softdevice I need check the run-time.
ANd i like to check the runtime.
So i used "app_timer_cnt_get...
I am nrf51822 QFACA1 chip with s130 softdevice using nordic_sdk_11.
ble_connectivity example was not working and i am unable to do a scan from my application board.
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
Hi all,
I have just buy a product use nrf51822 chip, I tried to find out SWIO and CLK pin out to flash but can not. Device only has RX and TX pin for Uart function, so I...
Hi.
I use nRF52 and I want to use DFU.
I want to make init packet because DFU need it.
To make init packet,
need master control panel.
I want to know how to get...
Hi There,
Is it possible to modify the number of BLE frames per connection interval (CI)? We are using nrf52832s and are only seeing one master request and slave response...
Hello,
can anyone tell me something about the security level of the connection like it is made in the Heart Rate Sensor Example. Is the connection encrypted or can everyone...
Hi all, I'm working on SDK11.0.0 experimental signed bootloader, I stored device type and device revision in uicr register now I need to update my bootloader through dfu and...
hi everybody.
Please help me on this
I use nRF51822 as iBeacon with ble_app_beacon in Nordic DK in below state:
only advertise in iBeacon mode
interval = 100...
Hi
Can we have both bluetooth and Gazell enabled at the same time?
We are using nrf51 series chips.
We want Gazell to communicate with with other nrf chips and Bluetooth...
