Hi,
If the following function is used, how to solve this error:
#include <nrfx_reset_reason.h>
void check_and_clear_reset_reason ( void )
{
// 获取复位原因
uint32_t...
2025-06-13T08:43:42.649Z INFO Initialising the bundled nrfutil device 2025-06-13T08:43:42.652Z DEBUG Started watching devices 2025-06-13T08:43:44.400Z INFO Using the bundled...
We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
Hi,
I want to change the GAP params such as connInterval, slaveLatency, and have some questions:
1.can I call sd_ble_gap_conn_param_update directly or need to send...
I used nRFgo Studio(version 1.15.1) to program S110 and application through my Jlink. But it's not worked in version 1.16.0.
It's not a good feature! :(
Is there any compatibility table for nRF51 series chips with revisions, softdevice versions and SDK versions?
I have some custom boards with a module that contains a nRF51422...
I'm trying to output a relatively high frequency PWM (300kHz). I'll need to adjust the duty cycle on the fly, without glitches and minimal time spent in IRQ handlers.
Currently...
I'm trying to build the ble_app_hrs example from Nordic's SDK on a Mac OSX 10.9.2 and have been following Nordic's nAN-29 Note v1.1 to install required tools, while looking...
Good day, I am using a USB to UART IC and it isn't working just because the nRF51822 Tx signal is inverted from this IC. There are some way to invert the UART signals?
I am building a new PCB board for a prototype. It will be used for proximity. It will blink on low battery. It also has a piezo speaker attached to a pin as well. My question...
Hi all. I'm now developing a triangulation solution for indoor robots as a project at my school. I have 4 radios, that I want to communicate with.
One master node send a...
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Attempting to program a softdevice hex file using Keil uVision and an ST-Link V2, I get:
No Algorithm found for: 10001000H - 10001013H
This is in the UICR (User Information...
Hello,
I am thinking about going to eindhoven the 20th of may for the nordic tech tour presentation.
My main interrest is the new v7.0 S110 softdevice which is to be released...
I have used the NRF51822 evaluation kit for a while now to design a product and it performed perfectly up until a few days ago: the onboard segger now fails to connect to...
hi,
i am using a light sensor which is SMBUS serial interface, i tried to interface twi of nrf51822 with the sensor, but i am not able to get acknowledgement from the sensor...
HI,
I'm using sd_app_evt_wait() for getting back to sleep mode between advertisings. I noticed that when I change the voltage in a small interval mode (40 ms between advs...
