Hello
I'm using an external flash to store large files, but I’d also like to use the SMP service to exchange small files over BLE. For that reason, I want to create a LittleFS...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi all,
I recently bought an nrf52840DK, and yesterday I tried to program an external board through the p20 connector on the DK with the SWD pins. I was able to flash the...
Hi, Using NCS 3.0.0 it would appear that the function sntp_simple_helper does not work with SYS_FOREVER_MS as a timeout value.
Problem: When we pass this value as a timeout...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
We start to migrate our equipment from nrf14L01 receiver to nrf51422 receiver in order to serve more equipment.
I am using nrf51822 to receive propietary protocols from heart...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
hi Ole Morten:
thank you for your great support.
i have tested nrf6310\temperature_example. at 30(Celsius)
I checked the data. NRF_TEMP=0x000002AF; TEMP=0xFFFFFFAC;...
Hi,
I need help on calculating the current consumption of our device when it is in advertise mode. So please answer the below questions.
What are all the significant...
Hello,
i would like to use HRM, HID, BAS and DIS profiles simultaniously. I used HID mouse example. I append required HRM things and it work almost properly. Problem is fault...
Hi, I'm a beginner. I want to add to example of the proximity, next service identical to battery service. I need to send 1 byte of data.
Everything works well until when...
I have an application that reads an nRF51822 pin configured as analog input and then sends that value using "ble uart" (included in Nordic's sdk). Analog input is read in...
Been studying the S110 5.x -> 6.0 migration docs. Are there any project-specifics / include-paths / Keil build-settings that must be updated as well?
Do I understand it...
Im stuck that i can't get my Motherboards to update. Just goes into an endless loop of saying toggle power to rest it, starting boo loader, Couldn't start.. etc etc..
Attached...
I have a nRF51822 device which has softdevice and bootloader.
And I'm trying upload my app with following steps:
make .bin file with gcc
Push the DFU button, and...
I'm running a custom nrf8001 board and the nrf8001 is consuming approx 6.2mA on it's own in advertisement mode using the uart demo. Has anyone had this same problem? Any advice...
Flash write and erase works fine, if ble is not initialized( ble_stack_init()).
Once ble is initialized, any write to NRF_NVMC->CONFIG hangs the system.
Do I need to...
Hello!
We are using a custom hardware design based on nRF51822. Recently we switched to the new chip version QFAAG0 with softdevice 6.0.0.
Our application needs a repeating...
