We are using the nRF5340 and our use case makes full use of all 4 shared peripherals for SPI and TWI as well as SPIM4. We want to add UART over USB and I was able to port...
Hello together, Which configurations or setup on the side of the Nordic nrf9161 DK has to be done to use the DEBUG IN connector for SWD? The board is powered by the 5VIN pin...
Hi,
I am developing for the 54l15 using nrf connect version 2025.5.92 Last Updated 2025-05-15, 10:08:43 and it's starting to seriously frustrate me.
The nRF Connecot for...
Hello, the CTE signal for Bluetooth AoA (Angle of Arrival) positioning is primarily transmitted over BLE advertising channels (37, 38, 39), corresponding to frequencies of...
:
I have seen three folder in the Thread lib path, there are: ftd, mtd, master.
I have some questions below, looking forward to your answer:
For FTD, are both cli...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
i am trying to customize my advertisement data, for that i am using sd_ble_gap_adv_set_configure API, and it is also returning error status 0. But the data what i am giving...
Hi
I dont know if this ever worked or stopped working after I updated SES to v4.5
The SES v.4,5 had no nrf support so I had to back down. (not sure why the update was...
Dear Sir,
To Nordic Dev kit, a sensor is interfaced via SPI lines. Using SPI in blocking mode (Polling).
After initializing SPI communication, 2 bytes are written to the...
nrf master control panel android app sent only one byte, while sending more than one byte gives Error 13 (0xd): GATT INVALID ATTR LEN
cant we send more than one byte in...
Hi,
I'm gathering assembly specifications for a custom PCB that uses nRF5340. I don't find any specific recommended reflow profile and solder paste for assembly. I stumbled...
Hi,
Bit of a newb question but I am evaluating the Thingy 91 dev board and would like to also connect some sensors via the SPI interface. I was wondering what would be the...
Hi everyone,
I have one question just for confirmation. Can I supply the board from the VDD pins located on P1 header (Socket 1x8)? Shall I bear something in mind in that...
Hi,
We use nRF9160 and nRF Connect SDK in a device project.
Our customer have asked to declare all open soruce software modules and their licenses. Do you have such a...
Hi, I found one older question (7 months ago) with the same problem but that had no answer. Situation:
- SDK 15.3, s132 v6.1.1 - The softdevice has been enabled and ble...
Hello,
I want to add/enable logs in DFU secure bootloader exaple. For that, I have enabled following macros which are needed.
NRF_LOG_ENABLED, NRF_ATFIFO_CONFIG_LOG_ENABLED...
Dear
I am testing AGPS with my THINGY91
SIMCARD: TELIA /Norway
I got the output report:
Could you tell me what is the problem? Telia SIMCard?
Thanks,
BR
...
Hi ,
I use SES to build a project ,SDK version is 15.2.And get the err:unknown register name 'vfpcc' in asm.
This seems to happen with every file.For example :
and...
Hello all,
I am working on nRF52840 EVM board.
I am not changing any thing in nRF52840 EVM board.
I was using nRF52840 board for downloading firmware in external custom...
I'm trying to use an MMA8652FC accelerometer with the nRF52832. When I call the function nrf_drv_twi_tx() the board hard faults, stopping in <SDK>\components\libraries\util...
In the case that I used custom board, I used bootloader_secure to OTA; but after OTA, the program doesn't jump to the application, even app nrf connect notify Sent Successfully...
