When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
We are trying to develop custom uart bootloader firmware without using MBR. also we are not using softdevice.
Here are some linker definitions which are implementation...
Hi! I'm working with a custom board, where pin p0.18 is connected to an external button.
I've read several posts, including this one which say that one must remove the ...
Hi, I'm unable to get a working example with the bootloader, softdevice and application. I'm following this: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts...
Hello There,
i have made an Selfmade PCBA with an nRF52810 and it is my first time that i am working with those Chips.
I have used the reference Design for this board...
Hi
I had a few questions about the nRF52833 SoC.
1. Is there a better way to transfer information through UART rather than using ( printf ) or ( NRF_LOG_INFO ) commands...
I have a similar error as described on https://devzone.nordicsemi.com/f/nordic-q-a/27626/access_model_reliable_publish-returns-nrf_error_invalid_param/109104#109104
I use...
Hi
I build the UartSecureDFU SDK to output a Window's EXE file, it send the upgrading aplication.zip to 52832 successfully in Window 7 System. But If build t he UartSecureDFU...
I have been debugging the TWI master of nRF52832 for a few days now and I have one more problem, which is very weird. For some reason, the master sends only the first read...
I am working with the mesh 4.0 light switch example and had a general question regarding a custom model I created based off the simple on off model.
During configuration...
Hi,
Our application sometimes hits a breakpoint in SoftDevice at either address 0xA60 or (less often) 0xA80.
Based on this post https://devzone.nordicsemi.com/f/nordic...
My question is very similar to this .
I am posting again since it did not seem to be answered.
The error originates from the following:
This happens when I am trying...
IAR IDE can be used to develop and dug the code of nRF52832 . However , IAR IDE can not programme the flash of nRF52832 directly . I need a kind of flash programmer tool ...
Hi all,
I am working with Segger ES on chip nRF52832 with nRF SDK for Mesh v4.0.
I am stuck now at message publication.
I have discovered that my code runs to packet_send...
Hi,
I'm using the nRF52832 with FreeRTOS and SDK 14.2.0 . I took a look at Profiling the Softdevice and FreeRTOS with Segger SystemView and Instrumenting with Segger SystemView...
Hello,
I am using nRF5 SDK v16.0.0 on nRF5232 PCA10040 DK.
I am trying to create an application that will count the number of button presses (GPIOTE events) using a Timer...
