Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
I'm trying to send data via UART from a NUCLEO-F401RE to the nRF 52840 DK. But the data I send is not comming through correctly. For example when I send 3 the nRF prints 32...
I have an existing product to which I need to add SPI to get Wifi compatibility. Basically the Nrf52 is acting as central and passes BLE events on to an ESP32 with Arduino...
Hi.
I have nrf52840-dk board. i tried the UART example from the peripherals directory. it works with the default, if i open a console on /dev/ttyACM0 and on /dev/ttyUSB0...
Wanted to ask if there is any example on configuring the GPS into single shot mode.
I know the asset tracker can operate in continuous_mode and continuous_power_saving_mode...
I am attempting to use SDK15 with the nrf52832 to communicate with multiple sensors over I2C. However, in the twi_sensor and twi_master_using_nrf_twi_mngr examples, as well...
I am using the nRF52840 with the SoftDevice disabled to run a proprietary RF protocol. For much of the time, I have the radio in continuous receive mode by making use of the...
I have a nrf52 application that samples four saadc channels at 1kHZ. That is: Map four pins to ADC input and let Easy DMA take care of the sampling so that the data is processed...
Hi,
I have measured QSPI current consumption on our product at no access period, and got 1mA (too high current!).
So I tried to check with nRF52840 DK to confirm our...
I need to have two different peripheral profiles (with different addresses and so) that will be advertising at same time and that can be connected by different centrals at...
Hello,
It might be a stupid question but I wonder if it is possible to use the ZCL generic command from the CLI to send ZDO commands? I tried it with the ieee_addr ZDO command...
We intend to use the ZigBee stack together with another communication stack and BLE. For the other stack we also have just a library (.a file).
Now we get an error message...
development setup: sdk: nrf5_sdk_15.3.0 LE protocol stacks: s112_nrf52_6.1.1_softdevice toolchain: MDK-ARM Professional 5.28.0.0 description： when we use ble HID or HEADSET...
I'm using the cli_agent_router example in nRF5 SDK for Thread and Zigbee v3.2.0 /4.0
I have a few questions:
1. If the end node needs to join in the designated coordinator...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I am working in a "peripheral" configuration. It has a characteristic that contains "Notify" as a property. Is there a way to check...
Hi,
Strange as this might sound: is there a way to gracefully force a softDevice assert such that I can get assert_nrf_callback() and see the call stack with DEAD_BEEF in...
