Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I am upgrading from v12.0 to 12.2. I am using Linux, Eclipse, GNU ARM and Eclipse managed make.
I get compiler error ...nrfsdk12.2/components/drivers_nrf/hal/nrf_gpio.h...
Device: PTR5528
Board: custom.
I have just given coin battery directly to VDD. At P0.00, P0.02 i have two leds. On p0.03 and 05 i am having one interrupt and other is...
Hello everyone.
I am currently working on a device with some peripherals.
I have SPI slaves and other sensors that I am monitoring using GPIOTE driver.
I noticed a...
I am attempting to implement buttonless DFU with my application.
Using SDK v12.2.0 on a Rigado BMD-300 module (nRF52832)
Starting one step at a time, using nRFgo Studio...
I am running RTC in nrf51, after coming out of sleep mode RTC is getting reset.I want this RTC to keep running so that we can use it as wake up signal.
I am attempting to enable a second custom service with a vendor specific UUID with three characteristics (in addition to an existing custom service and the battery service...
Hello
I have created one custom profile using "ble_app_uart" project. Now I have an issue that I can't able to remove UART part of the code. If I remove the UART part of...
Dear Team,
when we compile in keil on one of the system we are getting hex file as 30 KB(Programme application which is correct one) & in another system we are getting...
There are three devices I am using (i)acts as Peripheral (ii)acts as Central and Peripheral and (iii) acts as central.
I connected device#1 to device#2, then device#2 to...
hi everyone!
I'm trying to use BDS with NRF52-DK with last SDK version.
I read manual here
to start develop my custom service in BDS.
i create my service and characteristics...
what do I need to change in the android studio settings to compile the nrftoolbox source for a Nexus 6 (api v23)? I get a bunch of compiler errors (Error:(25) No resource...
I’m using nRF8001-R2Q32-T in my design, RF Balun (part number: 2450BM14A0002T), and 2.4GHz Chip RF Antenna (part number 2450AT18A100E). My question do I still use any network...
Is it possible to program an NRF51 to wake-up from SYSTEM ON by either RTC or external interrupt?
I have some sensors programmed to wake-up by RTC but I would also like...
