Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
It would be nice if libraries in the SDK contained more asserts about preconditions and postconditions. For example, since app_timer requires the lfclk running, the app_timer_init...
hi, i have downloaded nrf5-mpu-example sdk 13 from github. made necessary changes to work with sdk 14.2 for nrf52840. the kit is advertising when i check it in nrf connect...
How can I disable aes encryption?
I'm trying to port nRFgo gzll_host_w_dyn_pairing_example and the aes encryption peripheral is missing. Tried to define GZP_CRYPT_DISABLE...
Most of the SDK examples project support pca100028 only How I do Port in PCA20006
Right now I am using any IDE's . By using cmd , I generate hex file.
Where I have to...
Trying to port over code from UART example to muti-connect example.
Made sure include paths are correct, and made sure the following C files are in project.
ble_nus_c...
Hi guys,
I am using nrf51822 with SDK 11 and softdevice S130. I use Just Work bonding with Peer Manager. When I connect nrf51 with the Android phone run NRF Connect, the...
Hi,
Is there a way to obtain the connection handle inside the connection parameters event handler ( ble_conn_params_evt_handler_t ) on which the event occurred?
I am...
I've added a custom service for transferring data. It shall contain one characteristic that will notify when data is available, and the other should be a long read characteristic...
I recently got involved in a project where I am deploying a ble based mesh to understand and monitor bridge vibration patterns. I have been through nRF's mesh capabilities...
I am using the Arduino Primo board.
I have multiple beacons that advertise at a set interval.
All beacons have the same Device_name.
The Arduino Primo board scans for all...
Hello there. I just recently started programming using the nRF52832 DK, SDK14.1.0 and SoftDevice 132 v5.0 . I tried to follow this tutorial on Github: github.com/.../custom_ble_service_example...
I am using a power profiler to measure the timing of my program and I found something wrong. So I tested with a simple pure timer.
So first I set the timer during to 300ms...
I just spent 2 hours chasing BLE bug after upgrading from s132 v3 => v4.0.2
I added a call
// Configure the maximum ATT MTU.
memset(&ble_cfg, 0x00, sizeof(ble_cfg)...
I couldn't use nRF Connect (BLE) under Linux, after updating the FW, it tries to open /dev/ttyACM0 but fails to do so.
Not a "permission" problem: the user is in uucp...
