According to the nRF52832 Product Specification, “A step increase in supply voltage of 300 mV or more, with rise time of 300 ms or less, within the valid supply range, may...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi,
I noticed in the nRF54L QFN48 reference design, for the NRESET pin, there is an RC filter (1Kohm series R and 3.9pF shunt cap). What's this for and is it necessary?...
Hello,
I am using a nrf5340 dev kit. When I use SPIM the output from the pins gives the correct hex values but the output's amplitude is only around 100-200 mV. I know that...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I want to request AGNSS information from nrf cloud services using my nRF9151DK board. As a first step, I flashed the nRF Cloud multi-service application onto my DK...
Hi,
I'm using cdc_acm to create two COM ports on a PC -
// USB support
& zephyr_udc0 {
cdc_acm_uart0: cdc_acm_uart0 {
compatible = "zephyr,cdc-acm-uart" ;
...
Is there documentation missing from the SDK 6.0 docs (and 5.2) ?
For instance:
https://devzone.nordicsemi.com/documentation/nrf51/6.0.0/s110/html/a00125.html
is blank...
Hi All,
I am new to BLE nRF 51822 development kit. It is mounted on nRF go Starter Kit. My question is how can I put a advertising 51822 chip to sleep? Also, when I turn...
Hi
In my custom project I'm using pins P0.14 as SCL and P0.15 as SDA .
I know the pins selection #define is in twi_master_config.h. But the question is whether I have...
Hello,
I'm using: nRF51422-QFAA E00 and SDK - nRF51 5.2.0
Right now I'm running without softdevice enabled. I'm trying to use RTC1 Timer for my own delay_ms() function...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
I am currently using s120 to create a central device to scan for my peripherals. In addition I am trying to parse the Advertising Report data and send it via UART.
p_ble_evt...
I have use PAC10000 and RF51822 EVB ,when i run sniffer.exe,and I found nrf51822 ble,[0],
select "w " and show " Starting Wireshark",but always show " Starting Wireshark...
Hi All,
I need the slave node(S110) send advertising continuously and monitored by master node, so I set the advertising parameters as:
adv_params.type = BLE_GAP_ADV_TYPE_ADV_NONCONN_IND;...
hi all,
I use the Nordic BTLE SoC(nRF51) for develop product and now i have some issue for the the btle compatibility with other vendor btle.
Whether i use the dongle...
I would like to send the application, soft device and bootloader firmware versions
by means of the device information service.
How do I read the soft device firmware version...
I'm trying to write a test service on a PCA10001 that transmits a single scalar value that is computed from a few different sensor readings. I would like this service to send...
Hi everyone,
I have an interesting problem loading the S110 SoftDevice. First, loading version 6.0.0 onto the Evaluation Kit using nRFgo Studio works fine. However, loading...
hey,
I am new to eval kit and i am asking a very basic question, i want to send the RSSI from PCA10001 board to usb dongle PCA10000.i am looking the examples in sdk for this...
I'm seeing periodic disconnects with an iOS client application and the NRF_ERROR_SVC_HANDLER_MISSING which I gather may mean there is a compatibility problem with SDK and...
I try to use nrf51-ble-app-lbs with softdevice 7.0
I download ble-app-lbs at github.com/.../nrf51-ble-app-lbs
And change IROM1 start at 0x16000 lenth 0x29000.
...
