I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi: We develop our program based on (nrf51822 QFAAG0 1403AL), I found a serious problem that our new IC is (nrf51822 QFAAG2 1415AF), and the old program can't run on it any...
Not sure where to post this...
but there's a minor bug in components/toolchain/system_nrf52.c, where NRF_UICR->PSELRESET[0] is being checked twice to see if a reset pin...
While ota dfu via nrf toolbox android app, it sends wrong (0x15918) image size in start packet, and also bootloader starts writing softdevice image at address DFU_BANK_0_REGION_START...
Hi! I want to make a BLE network with 1 master (nRF51-DK) and multiples slaves (nRF51-dongle). I`ll send differents commands from master to slaves. This is for home automation...
Hello,
I am writing an application using SDK version 8.1 where I have a pin using the PORT event in nrf_drv_gpiote library. I have a need to disable the event temporarily...
I am encountering a problem with GPIOTE PORT events on the NRF51422 in a custom design. The chip occasionally seems to be able to get into a state in which the registers are...
Hello Guys,
I successfully used ble_hids_mouse and ble_hids_keyboard on my hardware but my final solution is a mouse + keyboard combo.
I merged the mouse and keyboard...
Hello,
I want to secure a link between 2 NRF51 (man in the middle and privacy with AES).
How to do that ? (I can use a static key in this application)
Most of the...
I want to create a single hex file that I can use to program the SD, DFU, and my application. I know I can use mergehex.exe to merge these files. To make it so that the bootloader...
Can anyone pls explain what is relation between advertising interval and advertising timeout..
Consider now i am setting advertising interval 1 second how i can prove or...
Hi Nordic,
I have got two PCA10028 boards and have a problem starting BLE on both.
I use latest Keil (5.16) and try to start ble_app_uart_s110_pca10028/ble_app_uart_s130_pca10028...
Hi
When implementing some characteristic handling i noticed, that in the newer softdevices the function "sd_ble_gatts_value_set" has changed to the following declaration...
Hi all,
I need to be able to check the matching networks on a design using the nRF51 series chip. My understanding of the procedure is,
Set up the board, enclosure...
