Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
hi guys ;
i have already an application on android phone that can read and write charchtéristic i also followed the tutorial Bluetooth low energy Characteristics, a beginner...
Hi,
I have an application where both radio notifications and flash operations are used.
It seems that every sd_flash_write() generates two radio notifications. So during...
Hello Everyone,
I am using raytac's BLE module (nrf51822 chip antenna version, 32kb RAM 256 kb Flash ) (www.raytac.com/download/MDBT40/MDBT40-ANT-D.pdf) in our product...
Hi,
I have a problem with NRF_LOG_INFO() macro - it only shows messages form main.c file but not from another .c files in project. Why this could happen?
I work in Eclipse...
Hello,
is it possible to use a external clock e.g. a digital output of a TXCO. As source for the LF clock. So the same clock source as used for the host uC can be used...
Hi!,
I'm newbie with nRF52. I have a nRF51 Development Kit and a nRF52 Development Kit.
I have installed nRFconnect (for Ubuntu 64 bits) in Fedora 24 Workstation (64...
Hi! I have tried to use USB CDC ACM in my project but after running the USB CDC ACM example in the SDK, I found out that the example have the issue of not sending the data...
Hello,
So I'm constantly reading data using i2c into a variable. How do I transfer the data in this variable to the pc? It's just an array.
I understand that I have...
I am looking for a smallest size transceiver with an antenna done as part of the PCB layout (no external antenna needed). The simplest RF PCB layout is preferred, single frequency...
Hi, I purchased a Sparkfun Breakout board for the NRF52832, but the bootloader on it seems to be extremely unstable. Hence, I've decided to flash the NRF52832 directly from...
Hello,
I already checked below link, but want to clarify the limitations of how many concurrent sessions are allowed in Soft Device initialize.
devzone.nordicsemi.com...
Hello,
i add a new custom service with one characteristic that allows me to send values over BLE with nRF connect, but i must send some acceptable values (-2, -4, 0, 4, 10...
Using SDK14.0.0, nRF52832, GCC, GDB/Ozone, secure DFU
This question seems to get close to asking about my problem.
I am trying to debug my application with a loaded...
Hi,
We made a custom PCB using the NRF52832 and followed the reference design. While everything else is working in our system, the BLE part is not working. We are using...
Hello,
I try to develop an application on a nRF51802 device. But this device is not managed in nRF_Drivers.4.0.0-2.alpha.pack from Keil software.
Is there an update...
