I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
I'm trying to understand how to handle error codes from the twi driver at the moment. When I hold my I2C slave in reset and try to configure it nrf_drv_twi_tx() returns 0x8201...
Hello,
in the electrical specification of the Timer peripheral (in the product specification page of the nrf52840 or nrf52832) it is said that there is 0.25us of delay between...
I have created a whitelist in nrf51822 device its working fine. But i stored whitelist details (pp_irk and pp_addr) to an external flash memory( bacause i not using peer manager...
I'm wondering if the extended advertisement feature of Bluetooth 5.0 is supported in any softdevice. If not, when can we expect it to be supported? Still within 2017 (as I...
Hi,
Each node has some state which should be saved in case of a power failure and recovered after it.
The problems:
how to detect the power failure?
where to save...
I have some Bluetooth LE v4.2 beacons that I will connect ONLY with known devices that we may call "readers". No consumer with use my beacons, I program them, I install them...
Hello everyone,
I am currently working on porting the InvenSense motion driver 6.12 to nrf52840pdk.
I followed porting guide provided by InvenSense. However, I met the...
First of all, I know the difference between the two roles, and I have also read through docs.
My question is actually limited to the current nordic mesh implementation....
I need a bootloader that I can use for my application that doesn't use a soft device and allows the firmware to be transferred through uart. Going through the forums, I found...
Common situation:
We have flashed dfu bootloader, and firmware uploaded into Flash via DFU. In this situation, DFU settings page contains correct CRC value for existing...
Because if there is, I'm not seeing it. It seems to me that the SDKv14 has asks you where you want your event handler function like this:
Where spi_0_event_handler() is...
HI,
I have been trying to generate the hex files for the mesh sdk (Latest) examples using cmake following the instructions in the documentation.
But the platforms supported...
Hi All,
I am starting an application using nRF51822 beacon kit.
I have some observation regarding current consumption.
1- erase entire flash and power up only, i can...
I'm trying to measure the startup time of the 32 MHz XTAL at the pins XC1 and XC2. Often a microcontroller will indicate in a register that the XTAL and internal PLL are stable...
