Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I'm trying to get the nRF52 on the PCA10040 dev board communicating through UART without the use of the programmer built into the dev board. So I'm connecting the UART pins...
Using the ble_app_uart example, if I pass more than get a maximum of 60 characters for each call to ble_nus_string_send I get a return code of NRF_SUCCESS, but the nRF UART...
Hello, we use an MDBT40 Module from Raytek with an nrf51822 chip.
We take this module for building a ble remote control.
The remote control is central and the receiver is...
Hello,
I Try to use nRFsniffer 1.0.1 on windows with Wireshark 2.0.1.
Wireshark seems to crash at startup. (reported bug 12103 on wireshark bugzilla)
Please provide...
I'm hoping someone here is familiar with the VL53L0X setup on a NRF52 board. I was able to get the single range measurements working just fine using polling and now I want...
I am using the PPK with SW v1.1.0 on a windows virtual machine on my mac. I'm testing custom hardware using the PPK regulator to supply power to my hardware.
There seem...
Maybe I understood something wrong, but I wonder if it is possible to have the nRF52840 handle file transfers like it does with the firmware hex-files.
Say, I want my nRF52840...
I am facing some issue, I am using HM10 ble module as peripheral and NRF52832 (Redbear NANO v2) as central device. I using SDK "nRF5_SDK_12.3.0_d7731ad" and example program...
Hello, deavteam. This is MANGO.
The Capacitive Touch on the nRF52 series blog post is really impressive.
I'm planning to start a haptic driver project using TI's DRV2605...
Hi all,
I am experimenting an issue similar to this guy --> devzone.nordicsemi.com/.../
But I have my project in two different branchs one using Peer manager and multiple...
when i use sdk14.2.0 and nrf52810 nus service send data， When the app transmits data for some time, the app prompts to disconnect, but the slave does not log any log prompts...
Still playing with my app. Since RTT (or whatever it was, when printf was printing info to segger debug console) was ruining the debug process, I just switched off RTT and...
Hi All,
I am new to nRF development and purchased the nRF51-DK (PCA10028). I have successfully experimented with the examples for ble_app_uart and lpcomp. My Application...
I have the beaconing/lightserver example working and being provisioned by the serial example. How might I now change the advertising of the beacon using the PyACI PacketSend...
Hello. I have a ttl converter ( https://goo.gl/images/uFSPHN) . Can I write a hex file through it? What are the possibilities to program so as not to buy a debug card?
