Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
When an interrupt with a printf in it triggers while another printf is still occuring the previous message is cutoff to print the next one.
Is there a way I can wait for...
Hi,
I've a custom board which has NRF51822 SOC and STM32 SOC. These two are connected over UART. In past I've successfully performed DFU OTA (BLE) for nrf51822 MCU, and...
I have got a Raytac module MDBT40(nRF51822) and development board nRF52832. Now I want to program the module using the development board. I have followed this video ( Programming...
Hello all,
I am trying to update my firmware using BLE peripheral.
I followed the instructions in this [tutorial] ( devzone.nordicsemi.com/.../)
I downloaded the SoftDevice...
Hello Nordic Forum!
Our product relies heavily in the TWI Bus, we use it to communicate with different sensors periodically. The most "important" one is read once every...
Hi,
We have made a custom board using the NRF52832 chip. The device is in hard fault mode and we believe it may be because of the corruption in internal memory. We wanted...
Hi,
Currently I am trying to test DCDC mode on my custom board nrf52832. After soldering 15nH and 10uH on DCC(pin 47), I issued the following command after softdevice enabled...
@Vidar: I have followed your steps in tutorial for "Development with GCC and Eclipse" and when I try to flash my device I get the below error
Nrfjprog.exe is not being...
Like many others (read a lot of threads here about this and also beneath the tutorial to Eclipse many people write that they suffer for it) i have problems in Eclipse with...
Hi,
I'm using the example dfu/bootloader_secure_ble for NRF52832 (PCA10040 board) in nRF SDK 13.0.0 version and on my mobile the "nRF Connect" application.
If I use...
Hello,
I'm working on a project based on the ble_app_multirole_lesc example, under examples/ble_central_and_peripheral/experimental and I found a bug.
In ble_evt_dispatch...
Hi,
I am using nrf52832 with sdk11 and s132.I am using ble_app_beacon example wherein I want to advertise with different address after one power cycle.
In ble_stack_init...
I have uploaded the Image with Keil µVision compilation errors, included Files in main.c and on the left side the compilation of micro_ecc_lib_nrf52.lib file using " build_all...
Hi there,
I'm trying to do a DFU over BLE using the Nordic nRF5x SDK on version 14.2. I'm using an NRF51 dongle on the PC side while trying to transmit to an NRF52832,...
