i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
I have installed this software several times without any result on PC.
How to access an IDE???
I am really very frustrated. Since several weeks I am not able to edit, compile...
When an interrupt with a printf in it triggers while another printf is still occuring the previous message is cutoff to print the next one.
Is there a way I can wait for...
Hi,
I've a custom board which has NRF51822 SOC and STM32 SOC. These two are connected over UART. In past I've successfully performed DFU OTA (BLE) for nrf51822 MCU, and...
I have got a Raytac module MDBT40(nRF51822) and development board nRF52832. Now I want to program the module using the development board. I have followed this video ( Programming...
Hello all,
I am trying to update my firmware using BLE peripheral.
I followed the instructions in this [tutorial] ( devzone.nordicsemi.com/.../)
I downloaded the SoftDevice...
Hello Nordic Forum!
Our product relies heavily in the TWI Bus, we use it to communicate with different sensors periodically. The most "important" one is read once every...
Hi,
We have made a custom board using the NRF52832 chip. The device is in hard fault mode and we believe it may be because of the corruption in internal memory. We wanted...
Hi,
Currently I am trying to test DCDC mode on my custom board nrf52832. After soldering 15nH and 10uH on DCC(pin 47), I issued the following command after softdevice enabled...
@Vidar: I have followed your steps in tutorial for "Development with GCC and Eclipse" and when I try to flash my device I get the below error
Nrfjprog.exe is not being...
Like many others (read a lot of threads here about this and also beneath the tutorial to Eclipse many people write that they suffer for it) i have problems in Eclipse with...
Hi,
I'm using the example dfu/bootloader_secure_ble for NRF52832 (PCA10040 board) in nRF SDK 13.0.0 version and on my mobile the "nRF Connect" application.
If I use...
Hello,
I'm working on a project based on the ble_app_multirole_lesc example, under examples/ble_central_and_peripheral/experimental and I found a bug.
In ble_evt_dispatch...
Hi,
I am using nrf52832 with sdk11 and s132.I am using ble_app_beacon example wherein I want to advertise with different address after one power cycle.
In ble_stack_init...
I have uploaded the Image with Keil µVision compilation errors, included Files in main.c and on the left side the compilation of micro_ecc_lib_nrf52.lib file using " build_all...
