Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
We are upgrading some products to SDK 14.2 and creating some new ones.
We need to start production programming of boards. I can't find the information on how to do this...
What is the maximum and minimum frequency of the PWM signal/square wave that can be measured on the NRF 52DK board I'm using NRF 52832.
Also, what is the max and min "pulse...
Hello,
I have found similar questions on transmitting multiple bytes over SPI, but I am still not sure how to do it. I want to communicate with a driver which needs to be...
Hi,
I found the 'Solar Sensor Beacon' example from
https://github.com/NordicPlayground/solar_sensor_beacon .
There, I found that no softdevice initialisation (nrf_sdh_ble_enable...
I am working through the nordic sdk 8.1 peripheral heart rate monitor example. I am wondering what RR is? I can't figure out what it stands for or what the purpose of it is...
Hi,
In my current project I have indicating LEDs connected via TWI bus. In this case, I can't use BSP_LED_0/BSP_LED_1 outputs to indicate states as it implemented in nrf_ble_dfu...
Hello, I recently use nrf52832 to make a wireless sensor network of BLE concurrently with NRF_ESB.
During development, I use only 2 sensor. Both sensors are connected to...
ANT S212, nRF52:
I've read all the links in the forum regarding serial port running in debug mode and not in run mode.
In my case, it works in RUN mode until softdevice_setup...
Hi
I have a sensor array which data have to be advanced burst to one or many devices.
The array size is anything from 24 bytes to 24k bytes, depending on the number of...
Hi guys,
I am using nrf51822 and SDK 11. I have some trouble about suddenly reset the nrf51822.
In my application, I used uart_fifo to received some information from other...
Hello beacon fellows,
with regards to maintenance, i am looking into the possibilities to avoid human presence when updating the message to be emitted by Beacon Kit. Any...
Hi,
I'm trying to do (customized / simplified) dual bank DFU on NRF52832 as simple as possible, without any complicated checks.
Assume I succeeded into storing the new...
i want to know about how nrf51822 beacon's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...