hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi,
How can we receive more than 20 bytes of data from the phone? We are using s132 and SDK 12.3. I know how to send more than 20 bytes of data from the NRF52 to the phone...
I am a newbie to Nordic chips and tools and new to bluetooth. My company is doing a BLE sensor. We have a prototype board ready and I am trying to do some firmware for it...
Hi I have tried the light demo example, where I do not understand the difference between "reply_Status" and "publish_State" on the server, then someone can explain the difference...
I am currently working with an NRF51822 and managed to change the TWI frequency to 400kHz in the twi_hw_master (this worked, I can see it on the oscilloscope). I commented...
I'm trying to upload via DFU from one nRF52832 to another nRF52832
I use SDK 14.1
First I want to enable CCCD at the master side.
static uint32_t cccd_configure(uint16_t...
Dear Sirs,
We are evaluating nRF52840 now, How far is the maximum range it can reach while keeping the data rate at 2Mbps if we use two nRF52840 for point-to-point communication...
i've been trying to generate hex files using keil uv5 from the examples given in the nrf52 sdk, the pregenerated hex files work as expected, wheras the ones generated by keil...
Dear Nordic Team,
Thanks for supporting.
I want to know How to add Manufacturing data with whitelist advertising . Already i am implemented without whitlist advertising...
Hello Team,
I have developed a sample Android application to use and control Nordic Thingy 52. I am able to control LED (Constant, Blink, Intensity). But I am not getting...
I want to test the mesh network for that i have to set the radio range of node to minimum distance so that i'll able to test the relay node example. Will you please help me...
Hello I am trying to make an electron application which is based from the 'pc-ble-driver-js' module for testing pupose for production development with nordic product
I am...
Hi all,
I using NRF52 kit and NUS service . When I add bond on NUS service , I still using nomal and I do not see the difference before and after I add bond . So , I want...
Hi. I am going down a rabbit hole. Wish to work with the SDK for Mesh using ideally the PCA10040 (nRF52832) and PCA10056 (nRF52840) kits.
1) Is this possible to mix the...
