Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
The download link of the installer for nRF-Command-Line-Tools and nRF-Connect-for-desktop does not change when I select different OS. It always shows the windows installer...
1/22/20 - Selecting version 10.5.0 of the CommandLine Tools for MacOS downloads a Windows.exe file
Selecting any version of the CommandLine Tools for any platform always...
Hello,
I was wondering if there are any plans to update pyaci to be able to accept the nRF Mesh app JSON file format.
It would be really nice if I could export a network...
Dear All,
I would like to develop BLE Beacon application based on (nRF52832_DK/nRF5_SDK_16_0_0/examples/ble_peripheral/ble_app_beacon).
However, I don't know the place...
Hi, I want to use the SAADC of the NRF52832
The board is Adafruit/ Bluefruit Feater.
The compiler is Arduino EDI I need to access to all the registers of the board or...
I built a device using the nRF52832 SOC, have programmed it with the Version 16 SDK>ble_app_uart_pca10040_132 using Segger Embedded Studio. I am able to connect to the nRF52...
Hi,
We are developing a product using NRF52832 chipset with a small 128*160 LCD (based on st7735s controller using 8 bit parallel interface).
I noticed that there is st7735s...
Are there any limitations that will not allow me to make the ble_app_hids_keyboard example with FreeRTOS?
If no, is there any examples that will help me easier to migrate...
Hi,
I see that Eddystone packets has service data limited to 20 bytes frame data. But unfortunately I have to encode more than 20 bytes.
So can I use advertise mode as...
Hello everyone.
I have made the next solution for merging softdevice into debug fw.
i 've added the next lines in ld script
MEMORY { SD_FLASH (rx) : ORIGIN = 0x00000000...
Hi,
I want to output a high & low voltage with an array, the array contains a sequence number, looks like: {0, 1, 0, 0, 0, 1, 1, 1, 1, 0, ...} , and the length of the...
I'm wanting to create and Android application that can communicate with a nrf24l01 module. Is there an android library available that will permit this? Thanks in advance!
Hello Everyone,
Consider i have 2 MCU's on board connected via UART interface, one is any ( Target ) MCU (MSP32, STM32, etc) and the other is Nordic's nRF52832 ( Host )...
Hi,
We have two nRF9160DK and both have the SIM card issue as below, and our development was blocked by this issue, so please help check it, thanks!
original case
Hi!
I am trying to figure out the app_timer_library but am running into some (to me) strange behaviour. For the first seconds it appears as if the LFCLK is running much...
