Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
I'm interested in using the chip and a very simple board. No buttons, no humidity or motion sensors, just the beacon (like a heartbeat). I'm trying to keep the price down...
Hi all,
I am using the experimental_ble_app_multiactivity_beacon example with S110 v7.1 and SDK 7.2. In particular the hrs_scanner app on the pca10028 board.
I am using...
Hi, I would just like to know if there's an equivalent to "BLE_GAP_EVT_CONNECTED" for services discovered. There's some stored data I want to send in a loop only after services...
Hi,
Does the nRF51822 have a capability of responding to multiple phones?
I am working with RFduino using the RFD22301. I'm assuming that the RFD22301 is the same BLE...
Hey,
the nRFgo Studio contains a simulator for the nRF8001 and 8002. Will there be an update in the near future to simulate the bahaviour of the nRF51 platform?
Mar...
I have TIMER2 running at 500us interval. ANT is working as 100Hz master.
Understood softdevice will affect the timing and cause some latency.
I am guessing it is delaying...
Hi:
I'm implementing an controller for an open source drone Crazyflie ( www.bitcraze.se/.../) . My device is similar to pca10001 board.
Since Crazyflie is acting as peripheral...
Hi all!
I've been unsuccessfully trying to DFU the Smart Beacon Kit with the latest firmware.
Using the nRF51 DK and the TC2030 tag connect cable I was able to program...
I am trying to get a communication between two pieces nRF51822 using the my service. I checked the peripheral with Master Controll Panel app and is working fine. The multilink...
Hi,
I have the (IoT) environment running. The Raspberry Pi (with Miredo tunnel) is connected to the outside world. I can ping6 the ipv6.google.com server from Rasperry...
Hi Team,
I am using nrf-51 DK as sniffer.
I need some guidance regarding how to study or analyze these packets?
I don't know what exactly I should check in each REQ...
Hello,
I am working on nrf51822, My requirement is to upgrade the firmware over the uart with help of DFU.
I have made code for that on controller side and fortunately...
In the release notes of the nRF51 SDK v8.0.0, section "Supported devices" it says that "This SDK is optimized for IC revision 3".
I am using a Laird BL600-SA-04 module...
