Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello, I'm using nRF51822-mKIT for a research.
To verify ADC readings from analog input, I've connected P0_5 to GND and ran the following code:
uint16_t adc_result;...
For my project I would like to use this bluetooth module: freqchina.en.alibaba.com/.../Fingertip_size_nRF51822_Module_Ultra_Low_Power_Bluetooth_4_0_Low_Energy_RF_Module.html...
I am trying to connect to a peripheral through s120 central and vendor has a 128 bit fixed UUID
I am trying to add it on central using sd_ble_uuid_vs_add(...,...) but it...
I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I'm able to read the characteristic's value by
BluetoothGattCharacteristic...
I'm using nRF51822 SoC and I have a LIS3DSH accelerometer connected to the ship via SPI bus . I used the SPI master example . So i used the switch_state() function then took...
Hi, I would like to know how I can immediately detect when a connection link is loss either from the central or peripheral. I need to know which error or notification to look...
Hello.
Here was the question about S120+DFU and Petter Myhre said that Nordic ready to release the new S120 version with the peripheral mode support, so making DFU OTA will...
Today I tried to update the SoftDevice of my project. I was working with the experimental NUS example with the old S310 SD (1.0.0). Because I want to communicate thru ANT...
Hello everyone,
I'm developing a security scheme in which the firmware verifies that the nRF51822 is the same as the one in the factory to which the firmware was installed...
Hi -- Can I run direct test mode on the nRF51-DK?
I've found the Direct Test Mode window in nRFgo Studio, but my board isn't available in the "Set up on ... " pulldown...
Hi,
I'm trying to implement a device including a PWM counter and a high resolution timer working with softdevice stack 110. Per the examples I got from this site, I'm using...
Hello! I'm trying to use s130 as peripheral.
I flashed nrf51822 with s130 stack. Opened peripheral example and build it with .ld file for s130.
After it I flashed this project...
we have a 2 chip soln. nrf for Ble, Atmel for main application.
config data is located in the Atmel part. Config data also has BT Device name, ADDR, Adv Params etc.
I...
