I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
hi Guys pls HELPPPPP
I have developing active rfID tag using nrf24L01+ and ATtinny13A, the program code is done perfectly, firstly I start developing the tag with separate...
Issue is related to:
devzone.nordicsemi.com/.../
Now I use latest SD S130_1.0
So, I added to my service characteristic with notifications enabled. But during discovering...
Hello,
I have a development kit with the PCA10000 and I can comunicate with the PCA10004 for about 5/6 meters what is ok for my application but now I want to comunicate...
Recently I needed to add some functionality, so the software could monitor when there was a ble gatt read characteristic event.
In the addCharacteristic code I simply set...
Hi, We have used nRF51 DK for developing an application where we used USB to load/flash the program code. Now we are in Pre-production stage where we can use only the nRF51422...
Hi,
I would like to extend the HTS service with measurement interval setting support. Bluetooth SIG specifies the measurement interval characteristic, which is easy to...
I'm using the example ble_app_hrs along with the HRM part of the nRF Toolbox iOS app . It makes sense to handle this in on_ble_evt in main.c but am unclear how I can recover...
Hi Team,
I am testing UART on nRF51 DK kit.
I have flashed uart_pca10028 .
I have taken out jumpers from P0.9(TX), P0.11(RX) and GND and connected to PC com port.
...
I have the example app working nicely now, so I want to export the project to a zip or something, effectively copy it, and put it elsewhere in my filesystem and work with...
Hi,
I tried installing the kernel (raspbian-kernel-zip Raspbian kernel for Raspberry Pi 3.17.4 ) on a Raspberry Pi 2 (Model B 1 GB). I found out that the Pi doesn't boot...
I'm trying the multilink central example with s120 and SDK 7.2 (because of simple_uart).
However, my PCA10028 board gets stuck at this macro:
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
My code is attached but essentially it is saying that SPI_MASTER_0 is not defined when I compile. I have the line:
#define SPI_MASTER_0_ENABLE /**< Enable SPI_MASTER_0...
I'm trying to get the ble_app_hrs working on PCA100001, the software installation is brand new (all installed today). I modified the pca100028 ble_app_hrs to try work with...
Hello everyone,
I have problems with my nRF51822. I think it is related to the starting memory address of softdevice. I attach 2 nRFgo's screenshots.
I have programmed...
