Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I'm designing custom board with nrf51822 SOC & using buck-boost converter for powering nrf chip, If I don't add inductors in DCC line how it will effect my custom board. ...
Hello,
In previous version of SDK, I used to use "sd_nvic_systemreset()" function to reset nRF52, but this function disappeared in SDK12.2.0 .
The question is what the...
Hello,
I am receiving the above error on Android BLE app while connecting to my pca10040 based board, and I developed this app with nRF Toolbox as a reference.
I am...
Hi all,
I have understood that sys_evt_dispatch is used for all events that aren't BLE but concern the softdevice.
I start to develop my code on gls_example, here in...
I have an application where I need to synchronize several devices to within 1us using a radio. In order to do this, we need to make a protocol that allows precise synchronization...
We have these Dev Kit Nrf52 and also Nrf51 Bluetooth Smart Beacon Kit. For our application and for the simplest user experience we would like to benefit from update via OTA...
My product only offer a debug interface（SWDIO/REST，SWDCLK，+3.3v，GND），but I learn that the nRF51 DK debug out interface has several pins，such as EXT VTG，EXT GND DETECT，EXT...
hi all:
I am a new user.Now i have a project in which I need to implement a function a host and four devices .I just want to know if i use the example of " gzp_dynamic_pairing...
Is a delay needed between Characteristic updates
I modified the ble_sdk_app_proximity example.
I added x3 services, based on the BLE Characteristics, a beginner's tutorial...
I have 32-bit float numbers, sent to the BLE from SPI.
I can manipulate this into x4 bytes, or actually use sprintf and get a real 6-byte representation of the number.
...
I have taken ble_app_ancs_c_s130_pca10028 example and modified the application to run on our custom board.
The custom board uses NRF51822 (NRF51 IC revision 3).
The following...
Hi,
We are using nRF51822_QFAB (128K/16K), S110 V8.0.0 and SDK V10.0.0 for my development. We are in the need of guest (unbonded), pairing and bonded mode.
Guest...
Hello,
I'm struggling with setting up the eclipse IDE to build the blincky program in the SDK now I've configured all the paths and eclipse configuration according to this...
