void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
This is referring to running a peripheral device on the PCA10028 eval board.
Let's say I have a connection interval of 100 ms, and a slave latency of 5.
So the BT stack...
Hello, I am using an nrf51822 but have no success in advertising.
I tried so far to load the ble_app_template from the peripheral examples where I' ve only changed
#define...
Hi,
I am looking for a BT module that can connect to both a BT Jabra audio headphones in addition to a BT HR chest strap with 2 live connections simultaneous.
Do I have...
I understand part of ram is used by the softdevice, but I see different addresses are used in different examples that use the same softdevice, namely S132. For example,
...
I am trying to run the examples given by Nordic on my nRF51 dongle. Most the examples are for PCA10028 or PCA10040 where as my dongle is PCA10031. I tried running them but...
Hi,
I need 6 PWM channels for a BLE project. Is there any solution to add 2 other pwm channels to nRF51822? If not, Which other Nordic ICs might be helpful instead?
Thank...
Hello,
I am using SDK 12.01 with softdevice (BLE application) and I want to write large data over flash. I am stuck with various issues.
When I try to write the data...
Hi,
I am having hard times to make SAADC working on DK-52, SDK13, S132. I need to perform a voltage measurement on command received from a connected device.
AIN pin...
Hi All
I am looking for the way to send and receive the string between nrf52 and mobile app.
what are the possible ways to do with minimum power consumption.
main concern...
Hi,
I've allready read a lot about using a static passkey on the DevZone and I have tried tons of things, but I just can't get it to work.
What I want is to connect...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi, I am playing with the SDK13 examples, UART (w/o softdevice). I use gnu gcc. The example runs and when I type q or Q the code goes to the printf(" \r\nExit!\r\n") as designed...
Hi
I read somewhere that when using internel ref for analog measurements the Vin changing does not influences the analog reading. Is that true?
Please, consider the circuit...
Hello,
I am looking through the data sheet for the NRF52 and do not see anything for writing to NVMC.
I see you can erase and configure the NVMC using:
NRF_NVMC ...
