Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hi,
I have a problem where I am getting NRF_ERROR_RESOURCES errors 2 out of 3 times when sending notifications from my peripheral to my central. I think this is caused because...
I have designed a custom board with a TF325J32K7680 32KHz clock with +-50ppm tolerance, for the 32MHz I am using the CX2016DB32000D0WZRC1 with +-40ppm tolerance.
Simple...
Hi,
Within each example in the NRF5 SDK there are a number of folders including
arm4
arm5_no_packs
armgcc
config
iar
I'm having trouble finding an explanation...
Hello everybody,
I used SDK14.2.0 , S132 .
I keep the data from nus_data in the uint8_t array. Then I am trying to write the array with use fds_write.
My fds_write...
Hi, I would like to add source files to Projects with a reltive path. The reason being that I would like to have my own code in a cloud based directory and code from SDK in...
Dear friend,
To u se the Power Monitor for current profile measurement of nRF52832, I prepare the board by doing both of the steps described below:
(1) Short solder bridge...
Hi There,
I currently using PCA10040 development kit for my project. I tried to merge with \nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_blinky\pca10040\s132...
Hi
We have a product with Nordic nRF9E5 coupled to Texas CC1190 amplifier.
We are seeing transients at start and end of TX; worst at end. We appear to be non-compliant...
Hello, we are using SDK 5.2.0, SoftDevice 6.2.1 S110 on the peripheral side and S130 on the central side.
We have implemented a serial data link between the two, the central...
I have made a custom PCB with the nRF52832, following the circuit reference, I used the C3 and L1 for tunning the antenna. Instead of a chip antenna I placed a wire in the...
The NRF_LOG library apparently uses memobj, which uses balloc. I assume that means I need to add some blocks in my sdk_config (i.e., MEMORY_MANAGER_SMALL_BLOCK_COUNT, etc...
Hello Guys,
I have some measurements for the determination of the maximum range and the energy consumption. The experiment is based on the ATT_MTU throughput example, nRF5_SDK_14...
Hi,
We have a BLE peripheral device that is used as a mouse/keyboard (nRF52832 SDK 14.0)
The peripheral pairs with most central devices just fine (including Mac and PC...
I have two nrf51 development board. A is PRX, B is PTX. now B can send payload to A , and A can receive and response it by ACK. But some times A want to send payload to B...
hi Nordic support team ,
i have sent my application data to nrf connect .I want to send that data when i write something in "write value " option in nrf connect .After comparing...
