The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
I was having some troubles using the app_timer (RTC1) shortly after mesh startup, so I enabled the PIN_IN_CB and PIN_IN_TS debug pins, and saw some interesting behavior. ...
Hello all,
am trying to configure 3 adc channels in a way to have conversion in 3 differents pins, without usin timer and ppi. so I implement the following code, the problem...
Hi
May i know what would be the debugging procedure using segger-RTT for nrf52840 and what is the debugging Hardware Required ?
Thanks and Regards,
R Madhu.
I know BLE5 is the future of IoT. I also want to invest on it.
But how to setup a complete BLE5 environment? In China, IPv6 has not been supported. Therefore, 6LowPAN/Thread...
Hi,
I want to ask a few question for ble_mesh.
What do these functions do:
rbc_mesh_persistence_set(..), rbc_mesh_tx_event_set(..)
Who should do the set operation...
hi Dear Engineers!
Have a question about external TIMER counter input hw PIN.
as Known, all the MCUs have a timer with external pin as a counter / capturer ability.
how...
I use STM32F4+nRF51822 through the SPI interface. I want to achieve nRF51822 DFU with SPI operation, now upgrade the simple LED to work properly. But can not work when using...
What i need is , am collecting the data from the sensor(which acts as a ble peripheral ) , the data which has to be transmitted to the ble central and that data should be...
Using the nrf52 DK, I was trying for hours to setup Segger IDE on a mac, and the software doesn't feel good to me, its not clear where is your code, it has too many libraries...
The vivo phone sometimes cannot scan the device,
There are two devices embedded same program.
However,one of them can be scanned,the other one can not.
The advertising...
Hi all, I'm working on sdk11.0.0 signed bootloader and I made change in it. Due to these changes bootloader size increased and not fit in the memory allocated to the bootloader...
Hello:
The product specification (v1.3, pg 263) says temperature sensor accuracy min = -5 C and max = +5 C.
Its not clear if these accuracy values correspond to the...
Hello,
I meet the same problem with the question " Status bit for sd_flash_write() ".I have register my flash_nrf52_sys_event_handler() in sys_evt_dispatch(),but after...
