Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately,which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
hello there when i am trying to open project C:\nRF51_SDK_8.1.0_b6ed55f\examples\ble_peripheral\ble_app_template - Copy\pca10028\s110\arm4. i am getting error like
Third...
Hi,
I have set connection interval as 1.8s.
But i have transmit data every 1 min.
I noticed that BLE transmits data every 1.8sec.
Can someone please tell me what is...
I have just exported a project from mbed, to the Keil uVision4 tool chain.
Create New Project "BLE_Thermometer" on mbed.
"BLE example for the Health-Thermometer...
I see in the information about the nRF51 talking about the support of 4.2. But it is not clear to me the extend of it. I am focus on the link layer and I would like to know...
Is it possible to implement 2 peripheral in one device (need to connect a peripheral device with two different centrals)? When should i expect for this feature?
I have a question about how much memory is required for app timers.
The comments for APP_TIMER_BUF_SIZE state that the buffer size must be one more than actually needed...
I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
Sorry,my English is poor. I
Now,I have four uart BLE device. Every device sends data in frequency 20Hz. And I also have a android phone. I hope that the phone could receive...
hi everyone.
i have an issue with app timer. i m using SDK 9 and softdevice v8.0. in my code i used ble_app_template project and changed something according to my goals ...
hi,
1.I find some same issues on website, most of them can send more than 1 packet per connection interval up to 6 packets, but I'm not sure what version of sofedevice...
Hi!
We are using S130 softdevice in peripheral role and achieve the specified maximum throughput of 63.4kbps ( S130 spec ) when communicating with a PC and connection interval...
Dear sir,
Reader has a NRF24L01P-R7 with stm32f4xx controller.We are using TAG chip NRF24LU1P-F32Q32-T.
Please share the independent stack information(source code) so...