Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm trying to setup a gazell application that could use the same resources of the Nordic SD.
Using the keil package manager, I switched the package configuration...
I'm going to configure nRF51822 chip as a spi slave.
And there are no more pins for the connector.
So I am trying to connect SS pin to the ground pin, instead to connect...
Hello
I'd like to write my own application for flashing nrf51822. It will add some additional information info hex file.
How can I burn hex file into the flash using...
Hi,
I was wondering if you can please clarify the licensing terms for the nrf51 softdevices?
I found the link to the SDK license here:
devzone.nordicsemi.com/.../license...
Hi,
I am trying to use GCC with Eclipse as explained in this tutorial , and after spending hours trying to figure it out, I am completely lost and ask for advices and help...
Hello,
It appears that changes were made to the DFU bootloader project in SD 8.1. The project no longer seems to function when using GCC.
I am using GCC 4.9.3
when...
I'm following these instructions. And downloading a project from this github repository.
The downloaded github zip file contains the following folder "ble_app_uart_c_S120...
Hello,
I use this program.I take values.Android Application want to show the values.
Program:
#include "ADXL345.h"
ADXL345 accelerometer(p5, p6, p7, p8);
Serial pc...
Hi all,
I would like to use the Arduino programming environment on my nRF51422 prototype. I have seen that RedBearLab has done the migration for the nRF51822 which quite...
Is the nrf52832 developer kit compatible with Arduino Leonardo? I know that most Arduino shields work well with Leonardo, but a few have troubles.
Thanks
Hi,
I would like to have a recommended supplier for the 32MHz crystal. I have seen the specification for the crystal. But from my experience it is a bit more complex than...
I followed the guide of this and when I opened the project " BLE_Gateway" ,it showed that the "spi_slave.c","softdevice_handle.c"and "ble_advdata.c" file couldn't be found...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
