Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
is there any complete altium designer file including schematic and pcb file for nrf51822 ?? there is only layout file in the website...... if you have it please email the...
Hi
I just updated our project to files from new SDK release 6.1. The normal application is working properly with the new SDK, but i got in trouble with the bootloader parts...
Hi all
I would like to use the s110 softdevice V7 with the nRF51422 which I know is possible. However, I would like to start the work with an example project, but I can...
I want to make a indoor positioning system using bluetooth 4.0. so for this HOST should recieve the RSSI from the devices it is connected to(from RSSI to distance conversion...
Hello,
I am working with the nRF8001 device:
When I try to configure the device as a service data broadcaster and go to the nRF8001 Setup -> Generate Source Files (in...
For improving my data trouchput (both directions, using »Write without response« and »Notification« like e.g. nRF Uart Example do9, I'd performed some tests regarding the...
I've been looking at the app_timer source after an odd lockup I had. I think it has a race condition in it.
The code which adds events to the pending events list is usually...
Dear All,
I am developing a custom service on 51822 and trying to adjust the packet number for each connection interval (I've split our data into 20 bytes chunks and they...
Hi, I got the DFU modify to use Synthesize clock (NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM) working with SD7 and SDK6. Tested on a board with the 32 KHz crystal, everything works...
Dear Sir/Madam,
One of our customer is using nRF51822 in the design and Proto has been completed. Customer is looking for the followings.
What all certifications...
Hello:
When I use Android 4.3 to connect nRf51822 AKII board, HEART RATE always show error on discovering services(129, then I can't connect nRf51822 AKII board.
Does...
Hello,
i want to develop open source software for nRF51 but i think the SDK licensing is to restrictive. I cannot use any of provided example code because its permits redistribution...
This is my code snippet
int main(void)
{
uint32_t err_code;
...
// Scheduler
scheduler_init();
// Initialize the SoftDevice handler module.
SOFTDEVICE_HANDLER_INIT...
Hello,
I was working over nordic dev board and found the uart template. but in that, only "data_receive_handler" is mentioned. i want to send data from my dev board to...
